HP ENVY x2 HP Envy x2 Maintenance and Service Guide IMPORTANT! This document i - Page 39

Digital media card reader board, Disconnect the digital media card reader cable

Get HP ENVY x2 PDF manuals and user guides View all HP ENVY x2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Digital media card reader board Description Digital media card reader Spare part number 702359-001 Before removing the digital media card reader, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the base enclosure (see Base enclosure on page 28). 5. Disconnect the battery cable (see Battery on page 29). Remove the digital media card reader board and bracket: 1. Disconnect the digital media card reader cable (1). 2. Remove the 2x2-mm broadhead screw on the rear edge of the board and then remove the 2 2x5-mm screws securing the digital media card reader board to the system board (2). The drive tilts upwards. 3. Remove the digital media card reader board and bracket (3). Reverse these procedures to reassemble and install the digital media card reader board. Component replacement procedures 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
Digital media card reader board
Description
Spare part number
Digital media card reader
702359-001
Before removing the digital media card reader, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the base enclosure (see
Base enclosure
on page
28
).
5.
Disconnect the battery cable (see
Battery
on page
29
).
Remove the digital media card reader board and bracket:
1.
Disconnect the digital media card reader cable
(1)
.
2.
Remove the 2x2–mm broadhead screw on the rear edge of the board and then remove the 2
2x5–mm screws securing the digital media card reader board to the system board
(2)
. The drive
tilts upwards.
3.
Remove the digital media card reader board and bracket
(3)
.
Reverse these procedures to reassemble and install the digital media card reader board.
Component replacement procedures
31