HP J8697A User Manual - Page 57

Getting Started With Switch, Configuration, Manager Password, IP Config DHCP/Bootp, IP Address

Get HP J8697A PDF manuals and user guides View all HP J8697A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Getting Started With Switch Configuration 3. Use the Tab key to select the Manager Password field and enter a manager password of up to 16 characters. 4. Tab to the IP Config (DHCP/Bootp) field and use the Space bar to select the Manual option. 5. Tab to the IP Address field and enter the IP address that is compatible with your network. 6. Tab to the Subnet Mask field and enter the subnet mask used for your network. 7. Press Enter, then S (for Save). The following is information on the fields in the Setup screen. For more information on these fields, see the Management and Configuration Guide which is on the ProCurve Web site. See page 5-1 for details. Parameter Default System Name blank Optional; up to 25 characters, including spaces System Contact blank Optional; up to 48 characters, including spaces Manager Password blank Recommended; up to 16 characters (no blank spaces) Logon Default CLI The default setting selects the command line interface for console access. The alternative is the Menu interface. Time Zone 0 (none) Optional; 1440 to -1440. The number of minutes your location is to the West (-) or East (+) of GMT. Community Name public Default setting recommended. Spanning Tree Enabled No Default setting recommended unless STP is already running on your network or the switch will be used in complex network topologies. Default Gateway blank Recommended; Enter the IP address of the next-hop gateway node if network traffic needs to be able to reach off-subnet destinations. Time Sync Method TimeP Optional; The protocol the switch uses to acquire a time signal. The options are SNTP and TimeP. TimeP Mode Disabled Synchronizes the time kept on the switch to the TimeP server. IP Config DHCP/Bootp Set to Manual unless a DHCP/Bootp server is used on your network to configure IP addressing. IP Address xxx.xxx.xxx.xxx Recommended; If you set IP Config to Manual, then enter an IP address compatible with your network. Note: The IP address and subnet mask assigned for the switch must be compatible with the IP addressing used in your network. For more information on IP addressing, see the Management and Configuration Guide which is on the ProCurve Web site. See page 5-1 for details. Subnet Mask xxx.xxx.xxx.xxx Recommended; If you entered an IP address, then enter a subnet mask compatible with your network. Getting Started With Switch Configuration 3-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
3-3
Getting Started With Switch Configuration
Getting Started With Switch
Configuration
3.
Use the Tab key to select the
Manager Password
field and enter a manager
password of up to 16 characters.
4.
Tab to the
IP Config (DHCP/Bootp)
field and use the Space bar to select the
Manual
option.
5.
Tab to the
IP Address
field and enter the IP address that is compatible with
your network.
6.
Tab to the
Subnet Mask
field and enter the subnet mask used for your
network.
7.
Press Enter, then
S
(for
S
ave
).
The following is information on the fields in the Setup screen. For more
information on these fields, see the
Management and Configuration Guide
which is on the ProCurve Web site. See
page 5-1
for details.
Parameter
Default
System Name
blank
Optional; up to 25 characters, including spaces
System Contact
blank
Optional; up to 48 characters, including spaces
Manager Password
blank
Recommended; up to 16 characters (no blank spaces)
Logon Default
CLI
The default setting selects the command line interface for console access.
The alternative is the Menu interface.
Time Zone
0 (none)
Optional; 1440 to -1440. The number of minutes your location is to the
West (-) or East (+) of GMT.
Community Name
public
Default setting recommended.
Spanning Tree Enabled
No
Default setting recommended unless STP is already running on your network
or the switch will be used in complex network topologies.
Default Gateway
blank
Recommended; Enter the IP address of the next-hop gateway node if network
traffic needs to be able to reach off-subnet destinations.
Time Sync Method
TimeP
Optional; The protocol the switch uses to acquire a time signal. The options
are SNTP and TimeP.
TimeP Mode
Disabled
Synchronizes the time kept on the switch to the TimeP server.
IP Config
DHCP/Bootp
Set to Manual unless a DHCP/Bootp server is used on your network to
configure IP addressing.
IP Address
xxx.xxx.xxx.xxx
Recommended; If you set IP Config to Manual, then enter an IP address
compatible with your network.
Note:
The IP address and subnet mask assigned for the switch must be compatible with the IP addressing used in
your network. For more information on IP addressing, see the
Management and Configuration Guide
which is on
the ProCurve Web site. See
page 5-1
for details.
Subnet Mask
xxx.xxx.xxx.xxx
Recommended; If you entered an IP address, then enter a subnet mask
compatible with your network.