HP Mini 110-3500 HP Mini 110, Compaq Mini CQ10 and HP Mini 1103 - Maintenance - Page 75

Remove the 2 Phillips 2.0×4.0 screws, Disconnect the power connector cable from the system board.

Get HP Mini 110-3500 - PC PDF manuals and user guides View all HP Mini 110-3500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

When replacing the system board, be sure that the following components are removed from the defective system board and installed on the replacement system board: ● SIM (see SIM on page 37) ● WWAN module (see WWAN and GPS modules (select models only) on page 43) ● WLAN module (see WLAN module on page 45) ● Memory module (see Memory module on page 47) ● RTC battery (see RTC battery on page 48) ● Fan/heat sink assembly (see Fan/heat sink assembly on page 64) Remove the system board: 1. Disconnect the power connector cable from the system board. 2. Remove the 2 Phillips 2.0×4.0 screws (1) that secure the system board to the base enclosure. 3. Lift the right side of the system board (2) until it rests at an angle. Component replacement procedures 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
When replacing the system board, be sure that the following components are removed from the
defective system board and installed on the replacement system board:
●
SIM (see
SIM
on page
37
)
●
WWAN module (see
WWAN and GPS modules (select models only)
on page
43
)
●
WLAN module (see
WLAN module
on page
45
)
●
Memory module (see
Memory module
on page
47
)
●
RTC battery (see
RTC battery
on page
48
)
●
Fan/heat sink assembly (see
Fan/heat sink assembly
on page
64
)
Remove the system board:
1.
Disconnect the power connector cable from the system board.
2.
Remove the 2 Phillips 2.0×4.0 screws
(1)
that secure the system board to the base enclosure.
3.
Lift the right side of the system board
(2)
until it rests at an angle.
Component replacement procedures
67