HP Pavilion dv7 HP Pavilion dv6 Entertainment PC - Maintenance and Service Gui - Page 54

Four Phillips PM3.0×3.5 screws, Four rubber isolators

Get HP Pavilion dv7 PDF manuals and user guides View all HP Pavilion dv7 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Removal and replacement procedures 4. Use the Mylar tab 1 to lift the hard drive up, and then slide it to the left 2 to release it from the hard drive bay. 5. Disconnect the hard drive cable 3 from the system board. 6. Remove the hard drive from the hard drive bay. 7. If it is necessary to replace the hard drive bracket or any of the hard drive bracket components, remove the following: a. Hard drive connector cable 1 b. Four rubber isolators 2 c. Four Phillips PM3.0×3.5 screws 3 that secure the hard drive bracket rails and Mylar cover to the hard drive. d. Left and right hard drive bracket rails with Mylar cover tabs 4. Reverse this procedure to reassemble and install the hard drive. Maintenance and Service Guide 4-15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
Removal and replacement procedures
Maintenance and Service Guide
4–15
4. Use the Mylar tab
1
to lift the hard drive up, and then slide it to the left
2
to release it from the hard drive bay.
5. Disconnect the hard drive cable
3
from the system board.
6. Remove the hard drive from the hard drive bay.
7. If it is necessary to replace the hard drive bracket or any of the hard drive bracket components, remove the
following:
a.
Hard drive connector cable
1
b.
Four rubber isolators
2
c.
Four Phillips PM3.0×3.5 screws
3
that secure the hard drive bracket rails and Mylar cover to the hard
drive.
d.
Left and right hard drive bracket rails with Mylar cover tabs
4
.
Reverse this procedure to reassemble and install the hard drive.