HP Scitex FB750 User Guide - Page 108

Troubleshooting upper lamp assembly installation,

Get HP Scitex FB750 PDF manuals and user guides View all HP Scitex FB750 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 108 highlights

c. Insert the spring-loaded clamp's dowels (A and B below) into the reflector. Figure 10-36 Inserting the dowels into the reflector 12. Re-install the user-end upper lamp assembly a. Slide the upper lamp assembly into the lower lamp assembly lining up the screw hole locations. b. Secure the upper lamp assembly to the lower lamp assembly using the original two lower screws on the user-end of the carriage ( A in Figure 10-29 User-end screws on page 96). c. Install the two screws that secure the upper lamp assembly to the carriage side plate (B in Figure 10-29 User-end screws on page 96 for locations). d. Connect the auxiliary cable to the top of the lamp. See Figure 10-27 Auxiliary cable on page 95. e. Connect the lamp power cable to the side of the lamp. See Figure 10-28 Lamp power cable on page 96. Troubleshooting upper lamp assembly installation ● If you have difficulty fitting the upper lamp assembly back into the lower lamp assembly, loosen the four screws indicated below. Re-fasten screws once assembly has been installed. Figure 10-37 Loosening screws to ease installation ENWW Replace the UV lamp bulbs 101

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
c.
Insert the spring-loaded clamp’s dowels (A and B below) into the reflector.
Figure 10-36
Inserting the dowels into the reflector
12.
Re-install the user-end upper lamp assembly
a.
Slide the upper lamp assembly into the lower lamp assembly lining up the screw hole locations.
b.
Secure the upper lamp assembly to the lower lamp assembly using the original two lower screws
on the user-end of the carriage ( A in
Figure
10
-
29
User-end screws
on page
96
).
c.
Install the two screws that secure the upper lamp assembly to the carriage side plate (B in
Figure
10
-
29
User-end screws
on page
96
for locations).
d.
Connect the auxiliary cable to the top of the lamp. See
Figure
10
-
27
Auxiliary cable
on page
95
.
e.
Connect the lamp power cable to the side of the lamp. See
Figure
10
-
28
Lamp power cable
on page
96
.
Troubleshooting upper lamp assembly installation
●
If you have difficulty fitting the upper lamp assembly back into the lower lamp assembly, loosen the
four screws indicated below. Re-fasten screws once assembly has been installed.
Figure 10-37
Loosening screws to ease installation
ENWW
Replace the UV lamp bulbs
101