HP Scitex FB750 User Guide - Page 26

Load roll-fed media with table-top roll holder, Multi-Image, Proceed

Get HP Scitex FB750 PDF manuals and user guides View all HP Scitex FB750 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

sheets can be of different sizes, and the image of a single size, be careful about job alignment and overprinting onto the belt. Again, as with multi-sheet printing with the same dimensions, the Multi-Image feature is selected from the Stored Jobs screen, following the same process. Because sheets can be of different sizes, and the images of various sizes, be careful about job size and alignment when selecting jobs. Load roll-fed media with table-top roll holder If the optional roll-fed media supply and takeup system with table-top roll holder is installed on the printer, you can print on roll-fed media in the following way. NOTE: See Table A-2 Media sizes on page 104 for a list of supported media sizes. 1. If installed, detach the rigid media output table from the printer, and set it aside. 2. Install the table-top roll holders into the holes on the input table, allowing the media to be loaded centered on the printer. 3. Load media onto the table-top roll holder, spooling off the top, with the media centered. NOTE: The table-top roll holder supports only print side out. NOTE: To prevent fingerprints from showing on printed output, wear gloves while handling the media. 4. Configure the media as explained in Configure media on page 11. At the end of the Configure Media process, press Proceed on the control panel. OR If the media is already configured, from the Home page of the control panel, press Load. NOTE: Be sure to enter the correct media thickness. The printer can detect the thickness of sheet-fed media only if the media is loaded under the media thickness sensor, which is located at the user end of the carriage rail. For roll-fed media (if enabled), use the manufacturer's specification or use a caliper to measure the thickness. 5. As prompted by the control panel, ensure that only a single foam roller is being used and is in the storage position. Pull media from the spool and feed it into the printer, use the forward and backward buttons and fans on and off selector on the control panel to assist. Then press Proceed. 6. Place the foam roller into its operating position and advance the media past the output roller. Then press Proceed. 7. Return the foam roller to its storage position, ensure that the vacuum fans are off and hold the Advance Media button for several seconds to assist in media tracking. Press Proceed to continue. 8. Place the foam roller into the operating position and make any final positioning adjustments. Press Proceed. 9. On the Select Thickness Units screen, press the option that corresponds to the units you will use. ENWW Load roll-fed media with table-top roll holder 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
sheets can be of different sizes, and the image of a single size, be careful about job alignment and
overprinting onto the belt.
Again, as with multi-sheet printing with the same dimensions, the
Multi-Image
feature is selected from the
Stored Jobs screen, following the same process. Because sheets can be of different sizes, and the images of
various sizes, be careful about job size and alignment when selecting jobs.
Load roll-fed media with table-top roll holder
If the optional roll-fed media supply and takeup system with table-top roll holder is installed on the printer,
you can print on roll-fed media in the following way.
NOTE:
See
Table
A
-
2
Media sizes
on page
104
for a list of supported media sizes.
1.
If installed, detach the rigid media output table from the printer, and set it aside.
2.
Install the table-top roll holders into the holes on the input table, allowing the media to be loaded
centered on the printer.
3.
Load media onto the table-top roll holder, spooling off the top, with the media centered.
NOTE:
The table-top roll holder supports only print side out.
NOTE:
To prevent fingerprints from showing on printed output, wear gloves while handling the media.
4.
Configure the media as explained in
Configure media
on page
11
. At the end of the Configure Media
process, press
Proceed
on the control panel.
OR
If the media is already configured, from the Home page of the control panel, press
Load
.
NOTE:
Be sure to enter the correct media thickness. The printer can detect the thickness of sheet-fed
media only if the media is loaded under the media thickness sensor, which is located at the user end of
the carriage rail. For roll-fed media (if enabled), use the manufacturer's specification or use a caliper to
measure the thickness.
5.
As prompted by the control panel, ensure that only a single foam roller is being used and is in the
storage position. Pull media from the spool and feed it into the printer, use the forward and backward
buttons and fans on and off selector on the control panel to assist. Then press
Proceed
.
6.
Place the foam roller into its operating position and advance the media past the output roller. Then
press
Proceed
.
7.
Return the foam roller to its storage position, ensure that the vacuum fans are off and hold the
Advance
Media
button for several seconds to assist in media tracking. Press
Proceed
to continue.
8.
Place the foam roller into the operating position and make any final positioning adjustments. Press
Proceed
.
9.
On the Select Thickness Units screen, press the option that corresponds to the units you will use.
ENWW
Load roll-fed media with table-top roll holder
19