HP Scitex FB750 User Guide - Page 36

Properties screen, Printing gt; Options > Eject Settings

Get HP Scitex FB750 PDF manuals and user guides View all HP Scitex FB750 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

◦ Press Job Storage Mode to choose whether jobs are printed and/or saved. ● Print & Save - Prints the job and saves it to disk. ● Save Only - Saves the job to disk without printing it. In this mode, the background color of the Stored Jobs section on the Home Page screen turns green. ● Print Only - Prints without saving the job to disk. ◦ Press Job Storage Sorting to choose how jobs are sorted. ● Press 2-Sided / Multi Image N-Up to set up a two-sided or multi-image N-Up print job using stored jobs. The printer prompts you to select the stored jobs that you want to use. All jobs must have the same color set and resolution. When printing two-sided, side one of the sheet is ejected to the input side of the printer, and you are prompted to flip over and reload the sheet to print side two. After printing, the sheet is ejected to the output side of the printer. TIP: When printing a two-sided print job from the stored jobs on the printer, and the Auto Eject feature is disabled (set to "Off" under Printing page > Options > Eject Settings), Auto Eject is enabled or the printer prompts you to change the Print Position setting before printing proceeds. This is because double-sided printing by definition uses the Auto Eject feature. If necessary, you can print the sides as two single-sided jobs, turning the sheet over between sides. Properties screen To view the properties of a Stored Job, or to print a Stored Job, press the job's thumbnail image. From the Stored Job properties screen, you can perform these operations on the print job: ● To print the job, press Load & Print. The printer will prompt you for the number of copies to print. If you have multiple sheets loaded, each copy will print on a separate sheet, and the printer will prompt for additional sheets until the number of copies requested have been printed. You can print the job in any print mode that use the same resolution as the original job. ● To adjust the right, left, leading, or trailing margins, press Margin Settings. The leading and trailing margins are applied to sheet-fed and roll-fed print jobs. ● To change the print mode of a job, press Print Mode. You can only change the mode to one that uses the resolution at which the job was RIPed. To print the job at a different resolution, re-send the job from the RIP at the new resolution. ● To delete the job, press Delete. ● To lock or unlock the job, press the appropriate button. Locking a job prevents it from being deleted, but subtracts from the available memory for Stored Jobs. TIP: If you want to print on a media type that is different from the media specified in a Stored Job, or if you will re-linearize the printer, do not reprint the Stored Job. For the best color, re-send the job from the RIP instead. When printing a job, the printer checks that the currently loaded media matches the media type that was loaded when the job was stored. If different, a warning is raised. You can choose to not print the job, or ignore the warning and print anyway. Printing on a media type or in a print mode that is different from the original job may result in a color shift. ENWW Stored jobs 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
◦
Press
Job Storage Mode
to choose whether jobs are printed and/or saved.
●
Print & Save
—
Prints the job and saves it to disk.
●
Save Only
—
Saves the job to disk without printing it. In this mode, the background color of
the Stored Jobs section on the Home Page screen turns green.
●
Print Only
—
Prints without saving the job to disk.
◦
Press
Job Storage Sorting
to choose how jobs are sorted.
●
Press
2-Sided / Multi Image N-Up
to set up a two-sided or multi-image N-Up print job using stored jobs.
The printer prompts you to select the stored jobs that you want to use. All jobs must have the same
color set and resolution.
When printing two-sided, side one of the sheet is ejected to the input side of the printer, and you are
prompted to flip over and reload the sheet to print side two. After printing, the sheet is ejected to the
output side of the printer.
TIP:
When printing a two-sided print job from the stored jobs on the printer, and the Auto Eject
feature is disabled (set to “Off” under
Printing page > Options > Eject Settings
), Auto Eject is enabled
or the printer prompts you to change the Print Position setting before printing proceeds. This is because
double-sided printing by definition uses the Auto Eject feature. If necessary, you can print the sides as
two single-sided jobs, turning the sheet over between sides.
Properties screen
To view the properties of a Stored Job, or to print a Stored Job, press the job's thumbnail image. From the
Stored Job properties screen, you can perform these operations on the print job:
●
To print the job, press
Load & Print
. The printer will prompt you for the number of copies to print. If you
have multiple sheets loaded, each copy will print on a separate sheet, and the printer will prompt for
additional sheets until the number of copies requested have been printed. You can print the job in any
print mode that use the same resolution as the original job.
●
To adjust the right, left, leading, or trailing margins, press
Margin Settings
. The leading and trailing
margins are applied to sheet-fed and roll-fed print jobs.
●
To change the print mode of a job, press
Print Mode
. You can only change the mode to one that uses the
resolution at which the job was RIPed. To print the job at a different resolution, re-send the job from the
RIP at the new resolution.
●
To delete the job, press
Delete
.
●
To lock or unlock the job, press the appropriate button. Locking a job prevents it from being deleted, but
subtracts from the available memory for Stored Jobs.
TIP:
If you want to print on a media type that is different from the media specified in a Stored Job, or if you
will re-linearize the printer, do not reprint the Stored Job. For the best color, re-send the job from the RIP
instead.
When printing a job, the printer checks that the currently loaded media matches the media type that was
loaded when the job was stored. If different, a warning is raised. You can choose to not print the job, or ignore
the warning and print anyway.
Printing on a media type or in a print mode that is different from the original job may result in a color shift.
ENWW
Stored jobs
29