HP Surestore Disk Array FC60 Storage Manager 60-NT Introduction Guide - Page 32

The associated hosts Omaha A and Omaha B

Get HP Surestore Disk Array FC60 PDF manuals and user guides View all HP Surestore Disk Array FC60 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Configuring Storage Arrays You have selected the host group Omaha node in the Topology View and are ready to configure a volume-to-LUN mapping. You are mapping the volume HResources to LUN 2. Note: If you would create a second volume-to-LUN mapping for host group Omaha using volume Marketing and LUN 7, you would have created Partition 3 as shown in Figure 7 on page 29. After you have defined the first specific volume-toLUN mapping (volume HResources using LUN 2) for host group Omaha, the host group and its associated hosts and host ports move out from under the Default Host Group. The associated hosts (Omaha A and Omaha B) can now access volume HResources. However, since they are no longer part of the Default Host Group they cannot access any volumes with default volume-to-LUN mappings. 32 CONFIGURING STORAGE ARRAYS

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
Configuring Storage Arrays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
32
C
ONFIGURING
S
TORAGE
A
RRAYS
)LJXUH±½
'HILQLQJ±D±9ROXPH¶WR¶/81±0DSSLQJ
%\±GHILQLQJ±WKH±VSHFLILF±YROXPH¶WR¶/81±PDSSLQJ±IRU±YROXPH±+5HVRXUFHV±XVLQJ±/81±¸·±WKH±
IROORZLQJ±UHVXOWV±RFFXU±LQ±WKH±7RSRORJ\±DQG±0DSSLQJV±9LHZ¹
7RSRORJ\±9LHZ±5HVXOW
)LJXUH±¶³
$±+RVW±*URXS±ZLWK±6SHFLILF±0DSSLQJV±LQ±WKH±7RSRORJ\±9LHZ
You are mapping the volume
HResources to LUN 2.
Note:
If you would create a second
volume-to-LUN mapping for host
group Omaha using volume
Marketing and LUN 7, you would
have created Partition 3 as shown in
Figure 7 on page 29
.
You have selected the host group
Omaha node in the Topology View and
are ready to configure a volume-to-LUN
mapping.
After you have defined the first specific volume-to-
LUN mapping (volume HResources using LUN 2)
for host group Omaha, the host group and its
associated hosts and host ports move out from
under the Default Host Group.
The associated hosts (Omaha A and Omaha B)
can now access volume HResources. However,
since they are no longer part of the Default Host
Group they cannot access any volumes with
default volume-to-LUN mappings.