HP Xw4600 HP xw4600 Workstation - Service and Technical Reference Guide - Page 92

IEEE-1394 card (optional), Removing an IEEE-1394 card

Get HP Xw4600 - Workstation - 2 GB RAM PDF manuals and user guides
UPC - 883585516483
View all HP Xw4600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

2. Open the PCI card retention clamp. Press the retention clamp levers down to unsnap, and then rotate them up (1). Figure 5-31 Installing a PCI card 3. Remove the PCI slot cover (2). 4. Align the keyed components of the PCI card with the slot , and then firmly seat the card in the slot (3). 5. Close the PCI retention clamp by rotating the clamp downward and pressing the two green clamp levers from the rear panel of the chassis (4). IEEE-1394 card (optional) This section describes how to remove an IEEE-1394 card. Removing an IEEE-1394 card To remove an IEEE-1394 card: 1. Disconnect power from the system (Predisassembly procedures on page 57), remove the side access panel (Removing the side access panel on page 61), and then remove the front bezel (Removing the front bezel on page 65). 82 Chapter 5 Removal and replacement procedures ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
2.
Open the PCI card retention clamp. Press the retention clamp levers down to unsnap, and then
rotate them up (1).
Figure 5-31
Installing a PCI card
3.
Remove the PCI slot cover (2).
4.
Align the keyed components of the PCI card with the slot , and then firmly seat the card in the slot
(3).
5.
Close the PCI retention clamp by rotating the clamp downward and pressing the two green clamp
levers from the rear panel of the chassis (4).
IEEE-1394 card (optional)
This section describes how to remove an IEEE-1394 card.
Removing an IEEE-1394 card
To remove an IEEE-1394 card:
1.
Disconnect power from the system (
Predisassembly procedures
on page
57
), remove the side
access panel (
Removing the side access panel
on page
61
), and then remove the front bezel
(
Removing the front bezel
on page
65
).
82
Chapter 5
Removal and replacement procedures
ENWW