Home » Honeywell Manuals » Thermostats » Honeywell CT3200 » Manual Viewer

Honeywell CT3200 Owner's Manual

Honeywell CT3200 Manual

Get Honeywell CT3200 PDF manuals and user guides

View all Honeywell CT3200 manuals

Add to My Manuals
Save this manual to your list of manuals

Honeywell CT3200 manual content summary:

Honeywell CT3200 | Owner's Manual - Page 1
MagicStat® CT3200 Programmable Thermostat Installation and Programming Instructions Weekday/Weekend (5-day/2-day) Programmable Heat and/or Cool Low Voltage (20 to 30 Vac) Thermostat and Mounting Plate Model CT3200 Welcome to the world of comfort and energy savings with your new Honeywell MagicStat®
Honeywell CT3200 | Owner's Manual - Page 2
. Contact your local waste management authority for instructions regarding recycling and the proper disposal of the old thermostat. M3701 Installation Verify that you have the right thermostat Make sure that the CT3200 is the right thermostat for your heating/cooling system. Read the compatibility
Honeywell CT3200 | Owner's Manual - Page 3
following parts: • Thermostat and mounting plate • Labels • Screws and anchors • Installation and Programming Instructions b. Gather the needed tools and supplies listed below. Required tools and supplies Optional tools • Two AA alkaline batteries. Honeywell recommends Energizer® • Wire cutter
Honeywell CT3200 | Owner's Manual - Page 4
panel. b. Remove the cover of your old thermostat (Fig. 2). c. Unscrew and remove the old thermostat's mounting plate from the wall, but do not disconnect the wires. d. Inspect the old thermostat wiring. If the wiring meets any of the following conditions, see the special wiring instructions on page
Honeywell CT3200 | Owner's Manual - Page 5
Step 3. Install the mounting plate Fig. 5 M20139 Fig. 6 M20129 Fig. 7 a. Separate the mounting plate from the thermostat using a coin, as shown in Fig 5. b. Position the mounting plate on the wall. Be sure the mounting plate sits flush against the wall and none of the wires are trapped behind it.
Honeywell CT3200 | Owner's Manual - Page 6
in degrees Celsius (°C), adjust screw C out one turn. d. You can install the batteries and program your thermostat now, or you can wait until the thermostat is mounted on the wall. To install the batteries, see the instructions on page 8. To program the thermostat, see the instructions that begin
Honeywell CT3200 | Owner's Manual - Page 7
to connect all of the old wires to the new thermostat. See the special wiring instructions on page 9 for details. c. Loosen the terminal screws and slip each wire beneath its matching terminal (Fig 10). d. Securely tighten the terminals. 69-0653-6 END OF WIRE VISIBLE HERE M20126 INSTALLATION 7
Honeywell CT3200 | Owner's Manual - Page 8
Fig. 13 Fig. 14 M1719C REMOVING BATTERY DOOR 8 INSTALLATION M20131 IMPORTANT: Batteries must be installed for programming and operation of the thermostat and heating/cooling system. Honeywell recommends using Energizer® batteries. a. Make sure that the System switch is set in the OFF position
Honeywell CT3200 | Owner's Manual - Page 9
page 2 for information about which programmable thermostat WILL work with your system. Three thermostat wires If you have three wires for heating only and can operate the fan using the fan ON switch, the 3200 thermostat will work with your system. Continue the installation procedure on page 4, step
Honeywell CT3200 | Owner's Manual - Page 10
15). Remove the jumper before wiring the R and Rc terminals. Fig. 15 JUMPER (FACTORY- INSTALLED). REMOVE IF 5-WIRE SYSTEM R Rc WY G M20127 Old thermostat terminals that do not match new thermostat terminals Use the table below to wire the new thermostat. Old thermostat terminal Connect to new
Honeywell CT3200 | Owner's Manual - Page 11
Run Program 2 Set Schedule Back Cooler Hold Temp 1 Fan Auto On System Cool Off Heat Descriptions 1 Fan switch-Selects automatic fan operation or fan on (page 17) 9 2 Set Schedule-Puts the thermostat into programming 10 mode (page 14) 11 3 Set Clock/Day-Sets the clock and day (page 12
Honeywell CT3200 | Owner's Manual - Page 12
once. The current time and day and the current temperature are displayed (Fig. 19). Fig. 19 Step 2. Learn about the programming features Your 3200 thermostat allows you to program schedules for both a heating season and a cooling season. • During the heating season, you will want to set the
Honeywell CT3200 | Owner's Manual - Page 13
and weekend Programming tips • You do not need to program times and temperatures for all program periods. If you decide not to program your thermostat, it will automatically control heating at 68°F (20°C), and cooling at 78°F (26°C), 24 hours a day. If you decide not to program weekend schedules
Honeywell CT3200 | Owner's Manual - Page 14
Time Temp Time Temp Time Temp WAKE 6:00 AM 70°F (21°C) LEAVE 8:00 AM 62°F (16.5°C) RETURN 6:00 PM 70°F (21°C) b. Set the System switch to HEAT. c. Press once. A blank schedule is displayed (Fig. 20). d. Set the Monday-Friday WAKE time by pressing or until the desired time is displayed
Honeywell CT3200 | Owner's Manual - Page 15
temperature j. Press again to display a blank schedule for the SLEEP program period and repeat steps h. through j. to set the program. k. Press to start the program. Step 4. Program the cooling schedule a. Write in the times and temperatures that you want to program for your cooling schedule
Honeywell CT3200 | Owner's Manual - Page 16
is below 50°F (10°C). d. Set the System switch to COOL, and the Fan switch to AUTO. e. Press until the setting is 10°F (6°C) below room temperature (Fig. 26). Your cooling system and fan should start. Note: When the cooling setting is changed, the thermostat may delay up to 5 minutes before
Honeywell CT3200 | Owner's Manual - Page 17
and the current temperature are displayed. Set the Fan and System switches The switches on the bottom of the thermostat faceplate (Fig. 16 page 11) control the operation of your only if the fan wire has been connected to the G terminal on the back of the thermostat. 69-0653-6 OPERATION 17
Honeywell CT3200 | Owner's Manual - Page 18
thermostat. However, if the display is blank, the batteries are dead or incorrectly installed and you will have to reprogram. See page 12 to begin reprogramming. e. Close the battery door and set the System switch to HEAT or COOL. Note: If "bAt Lo" continues to display after replacing the batteries
Honeywell CT3200 | Owner's Manual - Page 19
Override the program settings Note: Make sure the System switch is set to either HEAT or COOL before making any changes to the schedule. Change the temperature temporarily Press or displayed. until the desired temperature
Honeywell CT3200 | Owner's Manual - Page 20
Check the current programmed temperature Press to display the temperature that is programmed for the current program period. The SET indicator displays briefly along with the programmed temperature (Fig. 29). The display then returns to the room temperature. Check programs Press repeatedly
Honeywell CT3200 | Owner's Manual - Page 21
steady "bAt Lo" Temperature change occurs at the wrong times Heating will not come on Then... • Make sure the batteries are fresh and installed correctly. • Set the System switch to OFF. Remove the batteries and then insert them backwards for five to ten seconds to reset the thermostat. Replace the
Honeywell CT3200 | Owner's Manual - Page 22
or minus • 1° • Check that the System switch is set to COOL. Check the system fuse or circuit breaker and replace or reset if necessary. Check for correct wiring and good connections. If display is blank or says "bAt Lo," install fresh batteries. The thermostat has a built-in time delay on cooling
Honeywell CT3200 | Owner's Manual - Page 23
excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of one (1) year from the date of purchase by the consumer. If, at any time during the warranty period, the product is defective or malfunctions, Honeywell shall repair or replace it
Honeywell CT3200 | Owner's Manual - Page 24
Home and Building Control Honeywell 1985 Douglas Drive North Golden Valley, MN 55422 69-0653-6 Rev. 9-01 Home and Building Control Honeywell Limited-Honeywell Limitée 35 Dynamic Drive Scarborough, Ontario M1V 4Z9 Printed in the U.S.A. www.honeywell.com/yourhome

Section	Page
MagicStat® CT3200 Programmable Thermostat	1
Verify that you have the right thermostat	2
Step 1. Prepare for installation	3
a. Carefully unpack your new thermostat. Save your receipt and make sure you have the following p...	3
b. Gather the needed tools and supplies listed below.	3
c. Make sure that your heating and cooling systems are working properly. If there is a problem wi...	3
Step 2. Remove the old thermostat	4
Step 3. Install the mounting plate	5
Step 4. Set the thermostat for your type of heating system	6
Heating System Table	7
Note: Setting the screw “out one turn” means turning the screw 360˚ counter-clockwise, or one com...	7
Step 5. Wire the thermostat terminals	7
Step 6. Mount the thermostat	8
Step 7. Install the batteries	8
Special wiring instructions	9
A clock thermostat with C or C1 terminals	9
A clock thermostat has one or two extra wires attached to the C or C1 terminals that allow the cl...	9
a. Make sure that power to the heating/cooling system is turned off.	9
b. Locate the wires that are connected to the clock terminals marked C or C1.	9
c. As you disconnect the wires, do not allow these wires to touch.	9
d. Wrap the wires separately, using electrical tape to insulate the wires.	9
e. Place the wires where they will not interfere with the operation of the new thermostat. You wi...	9
f. Continue with the installation as instructed on page 4 at step 2e.	9
Six or more wires	9
If your old thermostat has six or more wires (excluding clock wires attached to the C or C1 termi...	9
Three thermostat wires	9
If you have three wires for heating only and can operate the fan using the fan ON switch, the 320...	9
Wires that are not connected to the old thermostat	9
If there are extra wires that do not connect to your old thermostat, do not label them. You will ...	9
Five wires connected to the old thermostat	10
Your new thermostat has a factory-installed metal jumper between the R and Rc terminals (Fig. 15)...	10
Old thermostat terminals that do not match new thermostat terminals	10
Use the table below to wire the new thermostat.	10
Step 1. Set the current time and day	12
Step 2. Learn about the programming features	12
Programming tips	13
Step 3. Program the heating schedule	14
a. Write in the times and temperatures that you want to program for your heating schedule.	14
Step 4. Program the cooling schedule	15
a. Write in the times and temperatures that you want to program for your cooling schedule.	15
b. Set the System switch to COOL.	16
c. Repeat steps 3c. through 3k. to program the weekday and weekend cooling schedule.	16
Step 5. Check out the system	16
Change the clock for Daylight/Standard time	17
a. Press once. The time is displayed.	17
b. Press and hold or until the correct time is displayed.	17
c. Press once. The current time and day and the current temperature are displayed.	17
Set the Fan and System switches	17
Replace the batteries	18
a. Make sure that the System switch is set in the OFF position.	18
b. Open the battery door.	18
c. Press on the left side of the batteries to remove them.	18
d. Install the new batteries. Make sure that the positive and negative terminals are oriented cor...	18
e. Close the battery door and set the System switch to HEAT or COOL.	18
Override the program settings	19
Frequently asked questions	21
Customer assistance	22
For all questions concerning this thermostat, please read and follow the instructions. If you nee...	22