Husqvarna M-ZT 52 Operation Manual - Page 49

Transmission Purging, With the bypass linkage closed and the engine

Get Husqvarna M-ZT 52 PDF manuals and user guides View all Husqvarna M-ZT 52 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

LUBRICATION Transmission Purging Due to the effects air has on efficiency in hydrostatic drive applications, it is critical to purge the system. These purge procedures should be implemented any time a hydrostatic system has been opened to facilitate maintenance or any additional oil has been added to the system. Resulting symptoms in hydrostatic systems may be: • Noisy operation. • Lack of power or drive after short term operation. • High operation temperature and excessive expansion of oil. • Shortened component life. Before starting, make sure the oil tank is at the proper oil level. If not, fill to the specifications outlined above. The following procedures are best performed with the vehicle drive wheels off the ground, then repeated under normal operating conditions. See Moving Machine By Hand in the Operation section for bypass linkage adjustments. 1. Disengage the brake if activated. 2. With the bypass linkage open and the engine running at fast idle, slowly move the directional control in both forward and reverse directions (5 or 6 times). As air is purged from the unit, the oil level will drop. 3. With the bypass linkage closed and the engine running, slowly move the directional control in both forward and reverse directions (5 to 6 times). Check the oil level and add oil as required after stopping the engine. 4. It may be necessary to repeat Steps 2 and 3 until all the air is completely purged from the system. When the hydraulic drive operates at normal noise levels and moves smoothly forward and reverse at normal speeds, the hydraulic drive is considered purged. 5. After the vehicle has been used two times, the oil level should be checked while the oil is cold and adjusted accordingly. 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
49
LUBRICATION
Transmission Purging
Due to the effects air has on efficiency in hydrostatic
drive applications, it is critical to purge the system.
These purge procedures should be implemented
any time a hydrostatic system has been opened to
facilitate maintenance or any additional oil has been
added to the system.
Resulting symptoms in hydrostatic systems may be:
•
Noisy operation.
•
Lack of power or drive after short term operation.
•
High operation temperature and excessive
expansion of oil.
•
Shortened component life.
Before starting, make sure the oil tank is at the proper
oil level. If not, fill to the specifications outlined above.
The following procedures are best performed with the
vehicle drive wheels off the ground, then repeated
under normal operating conditions.
See
Moving Machine By Hand
in the
Operation
section for bypass linkage adjustments.
1.
Disengage the brake if activated.
2.
With the bypass linkage open and the engine
running at fast idle, slowly move the directional
control in both forward and reverse directions (5 or
6 times). As air is purged from the unit, the oil level
will drop.
3.
With the bypass linkage closed and the engine
running, slowly move the directional control in
both forward and reverse directions (5 to 6 times).
Check the oil level and add oil as required after
stopping the engine.
4.
It may be necessary to repeat Steps 2 and 3 until
all the air is completely purged from the system.
When the hydraulic drive operates at normal noise
levels and moves smoothly forward and reverse at
normal speeds, the hydraulic drive is considered
purged.
5.
After the vehicle has been used two times, the oil
level should be checked while the oil is cold and
adjusted accordingly.