IBM 62174DU Installation Guide - Page 37

Drive clip

Get IBM 62174DU - IntelliStation A - Pro 6217 PDF manuals and user guides
UPC - 000435924971
View all IBM 62174DU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Drive clip 11. Push the drive into the bay. 12. Determine whether the drive is an IDE or SCSI device; then, connect one end of the applicable signal cable into the back of the drive and the other end of this cable into the applicable IDE or SCSI connector on the system board. See "Power and signal cables for internal drives" on page 29 for additional information about cabling drives and "System-board internal connectors" on page 14 for the location of IDE and SCSI connectors on the system board. If there are open connectors on the cables connecting existing IDE or SCSI drives, you can use these cables to connect the new drive. 13. Route the signal cable so that it does not block the airflow to the rear of the drives or over the microprocessor. 14. Connect the power cable to the back of the drive. The connectors are keyed and can be inserted only one way. 15. If you have other options to install or remove, do so now; otherwise, replace the bezel and support bracket and then go to "Completing the installation" on page 40. Chapter 2. Installing the hardware 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
Drive clip
11.
Push
the
drive
into
the
bay.
12.
Determine
whether
the
drive
is
an
IDE
or
SCSI
device;
then,
connect
one
end
of
the
applicable
signal
cable
into
the
back
of
the
drive
and
the
other
end
of
this
cable
into
the
applicable
IDE
or
SCSI
connector
on
the
system
board.
See
“Power
and
signal
cables
for
internal
drives”
on
page
29
for
additional
information
about
cabling
drives
and
“System-board
internal
connectors”
on
page
14
for
the
location
of
IDE
and
SCSI
connectors
on
the
system
board.
If
there
are
open
connectors
on
the
cables
connecting
existing
IDE
or
SCSI
drives,
you
can
use
these
cables
to
connect
the
new
drive.
13.
Route
the
signal
cable
so
that
it
does
not
block
the
airflow
to
the
rear
of
the
drives
or
over
the
microprocessor.
14.
Connect
the
power
cable
to
the
back
of
the
drive.
The
connectors
are
keyed
and
can
be
inserted
only
one
way.
15.
If
you
have
other
options
to
install
or
remove,
do
so
now;
otherwise,
replace
the
bezel
and
support
bracket
and
then
go
to
“Completing
the
installation”
on
page
40.
Chapter
2.
Installing
the
hardware
25