Icom IC-718 Instruction Manual - Page 17

Frequency Setting - split mode

Get Icom IC-718 PDF manuals and user guides View all Icom IC-718 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

∫ √ 4 FREQUENCY SETTING s When first applying power (CPU resetting) Before first applying power, make sure all connections required for your system are complete by referring to Chapter 3. Then, reset the transceiver using the following procedure. Resetting CLEARS all programmed contents in memory channels and returns programmed values in quick/initial set mode to default values. q Make sure the transceiver power is OFF. w While pushing and holding [∫ UP] and [√ DN], push [PWR] for 1 sec. to turn power ON. • The internal CPU is reset. • The transceiver displays its initial VFO frequencies when resetting is complete. e All quick/initial set mode settings are returned to default values. (p. 41) [PWR] √ [√] [∫] Under cooler temperatures, the LCD may appear dark and unstable after turning power ON. This is normal and does not indicate any equipment malfunction. s Initial settings After resetting the transceiver, set controls and switches as shown in the figure below. CCW : counterclockwise [METER]: Po [POWER]: OFF ∫ [AF]: Max. CCW [LOCK]: OFF [RF/SQL]: 12 o'clock [RIT]: Center [IF SHIFT]: Center Turn power ON, then check the display. If any of the following indicators appear, turn them OFF as follows: • Quick tuning step indicator "w" : Push [TS]. • 1 Hz frequency readout : Push [TS] for 1 sec. (while quick tuning step is OFF) • RIT indicator " RIT " : Center. • Split indicator " " : Push [SPL]. [NB], [COMP]: OFF [P.AMP], [ATT],: OFF 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
4
15
FREQUENCY SETTING
■
When first applying power
(CPU resetting)
Before first applying power, make sure all connec-
tions required for your system are complete by refer-
ring to Chapter 3. Then, reset the transceiver using
the following procedure.
Resetting
CLEARS
all programmed contents in
memory channels and returns programmed values
in quick/initial set mode to default values.
q
Make sure the transceiver power is OFF.
w
While pushing and holding [
∫
UP] and [
√
DN],
push [PWR] for 1 sec. to turn power ON.
•The internal CPU is reset.
•The transceiver displays its initial VFO frequencies
when resetting is complete.
e
All quick/initial set mode settings are returned to
default values. (p. 41)
■
Initial settings
After resetting the transceiver, set controls and
switches as shown in the figure below.
[PWR]
√
√
[
√
][
∫
]
∫
∫
[METER]: Po
[LOCK]: OFF
[POWER]: OFF
[P.AMP],
[ATT],: OFF
[RIT]: Center
[IF SHIFT]: Center
[AF]: Max. CCW
[RF/SQL]: 12 o'clock
[NB], [COMP]:
OFF
Turn power ON, then check the display. If any of the
following indicators appear, turn them OFF as follows:
•Quick tuning step indicator “
▼
” : Push [TS].
•1 Hz frequency readout
: Push [TS] for 1 sec.
(while quick tuning
step is OFF)
•RIT indicator “
”
: Center.
•Split indicator “
”
: Push [SPL].
RIT
RIT
Under cooler temperatures, the LCD may appear
dark and unstable after turning power ON. This is
normal and does not indicate any equipment mal-
function.
CCW
: counterclockwise