InSinkErator Model C1300 Owners Manual - Page 4

1/4" copper tube 3 aMounting the tank 5 aFinal Water Connection­ Tank must be mounted level S  elect a spot under the sink to mount Brass Nut tank vertically within reach of both Ferrule Brass Insert plumbing and electrical connections. Brass Nut Brass Nut BraFses rNruutle Brass Insert Ferrule Ferrule InstallBarasTs -Nfuittting (not included) onto the cold Fwerarutleer supply line. Brass Nut Install dedicated water control valve to ensure proper operation. The tank should be within 16" or less of faucet water lines and within 30" or less of a standard grounded outlet. 1/4" copper tube Brass Insert 1/4" copper tube with Ferrule 1/4" 1/4" compression fitting. copper tube A t the end of the copper 1/4" tube, slide the fitting's brass nut and ferrule W  hile holding tank in place on over the tube. 1 2 ­Property Damage: Tank must be located the spot selected for installation, use a pencil to mark locations for Property Damage: Join remaining Insert the copper tube into the 1/4" compression fitting and tighten. within 16" of faucet and within 30" or less 2 hanging screws. tube to cold water supply only. of a standard grounded outlet. DO NOT extend plumbing or electrical lines. b Leave 1/4" for hanging tank. 3 1 2 FILL TANK & then CONNECT POWER BrassNut 6 a Screws provided are for use Brass inNut wood studs or cabinets only. Use wallFaerrnulechors (not supplied) for installation into drywall. Brass Insert 1 2 Ferrule Brass Insert Brass Nut Brass Nut coppF1e/e4rr"rtuulbee Brass Nut Ferrule Ferrule Brass Insert Brass Nut T  urn on the cold water supply. Ferrule D epress the dispenser handle and hold it until water flows from the spout. P re-drill 1/8" pilot holes at marks. T urn screws into pre-drilled holes, 1/4" copper tube Rfluusnhtlhineceowsp.ap1et/e4r"rtufboer at least 2 minutes to 1 Mount tank vertically in an area that allows clearance on the underside of the tank for drainage, if necessary. DO NOT over tighten screws. 3 2leaving 1/4" exposed. H ang the tank on the screws. T ighten the screws with only 1/2 turn clockwise. 3 Scalding Hazard: The faucet dispenses near boiling (212ºF) water, which can instantly cause scalds or burns. Use care when operating this appliance. 4 Connecting Faucet to Tank a1 2 W  ithout depressing the gray button, b C  heck all connections to ensure they are tight and that there are no leaks. P lug in instant hot water tank. (1) 2 (2) (3) 3 place the snap-connect fitting at the end of the blue 1/4" tube onto the left fitting on the tank, pushing until it clicks into place. (1) S  lip the flexible white 7/16" tube over barbed middle fitting and slide down approximately 1/2". (2) Property Damage: A standard grounded outlet within 30" of the dispenser is required under the sink. Do not use an extension cord set with the dispenser. Water will be cold at first. Allow 12-15 minutes for water to reach target temperature. Gurgling or hissing is normal during the initial heating cycle. 3 3 2 Property Damage: Pinched or blocked water lines may cause damage to the dispenser tank. Check to make sure tubes are connected properly and are pushed down as far as possible. S  lip the clear 5/16" tube over the far right smooth fitting and slide down approximately 1/2". (3) V  isually check for pinched or crimped tubes. Hose clamps are not needed for any of the connections. Personal Injury: This tank is a non-pressurized tank. DO NOT modify this system. DO NOT close vent tube or connect other type dispensers or valves to the tank. Use only the InSinkErator dispenser faucet supplied. Use only parts provided. Contact an authorized InSinkErator Service agent for repairs or replacement components. Fire Hazard: To minimize possibility of fire, DO NOT store flammable items such as rags, paper or aerosol cans near the tank. DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Property Damage: To avoid water damage, replace any loose or split tubing. Periodically inspect the unit for ‑a‑ny signs of leakage and immediately remove from service any unit suspected of leaking. For Technical Assistance 6 1-800-845-8345 7