InSinkErator Model C1300 Owners Manual - Page 6

Manual del usuario

Page 6 highlights

TROUBLESHOOTING PROBLEM Water and steam spits forcefully from spout without turning on the dispenser faucet. POSSIBLE CAUSE • Unit is boiling. May be normal during initial setup. WHAT TO DO • Activate faucet lever to release some water from the tank. • Adjust water temperature using dial on tank front. Remember that at higher altitudes, water boils at lower temperatures. Water is not hot. • The unit may not be plugged in. • The electric outlet is inoperative. • Make sure the unit is connected to a properly grounded electric outlet. • Make sure the circuit breaker or fuses are functioning properly. • Check that the outlet is not switched off. Water is too hot or not hot enough. • Thermostat is not adjusted to your needs. Water comes out the vent instead of spout. • Outlet tube is blocked. • A djust the thermostat slowly, then activate faucet handle for 20 seconds to bring in fresh water to be heated at the new setting. Allow 5-7 minutes for water to reach new temperature. • Check that outlet tube is not kinked, twisted or pinched. • Unscrew spout end piece and clean out any debris. Water is dripping from the spout/vent intermittently. • The expansion chamber isn't draining properly due to low water pressure. • The spout is blocked. • Unplug the unit. If the dripping doesn't stop after a few minutes, check the supply valve to ensure that is fully open and there are no obstructions in the water line reducing the pressure below 30 psi (i.e., a poorly mounted saddle valve, a clogged water filter, or a partially opened shut-off valve). • Unscrew spout end piece and clean out any debris. Water is dripping from the spout/vent constantly. • Debris in the water line may be • Unscrew spout end piece and clean out any debris. in the faucet valve seat causing a slow water leak. • Activate faucet lever 7-10 times to flush faucet & lines. Water discoloration/ rusty appearance. • Corrosion of unit. • Unplug and drain unit as described in the Seasonal Storage/ Drainage Section on page 8 of this manual. If the water discoloration remains after draining and refilling unit, discontinue use and contact an authorized InSinkErator service agent. If you are still experiencing trouble, visit www.insinkerator.com/foodservice or call 1-800-845-8345. An instant hot water dispenser, like any water heater, has a limited life and will eventually fail. To avoid possible property damage, this instant hot water dispenser should be regularly examined for leakage and replaced when necessary. A drain pan, plumbed to an appropriate drain or outfitted with a leak detector, should be used in those applications where any leakage could cause property damage. C1300 H778 Dispensador de agua caliente instantánea Manual del usuario Instalación, cuidado y uso Installation, Care & Use Installation, soin et utilisation 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16

Dispensador de agua caliente instantánea
Manual del usuario
Instalación, cuidado y uso
Installation, Care & Use
Installation, soin et utilisation
C1300
H778
TROUBLESHOOTING
WHAT TO DO
Water and steam spits
forcefully from spout
without turning on the
dispenser faucet.
Water is not hot.
• Unit is boiling.
May be normal during initial setup.
• The unit may not be plugged in.
• The electric outlet is inoperative.
• Activate faucet lever to release some water from
the tank.
• Adjust water temperature using dial on tank front.
Remember that at higher altitudes, water boils
at lower temperatures.
• Make sure the unit is connected to a properly grounded
electric outlet.
• Make sure the circuit breaker or fuses are
functioning properly.
• Check that the outlet is not switched off.
Water is too hot
or not hot enough.
• Thermostat is not adjusted to
your needs.
Adjust the thermostat slowly, then activate faucet handle
for 20 seconds to bring in fresh water to be heated at
the new setting. Allow 5-7 minutes for water to reach
new temperature.
Water comes out the
vent instead of spout.
• Outlet tube is blocked.
• Check that outlet tube is not kinked, twisted or pinched.
• Unscrew spout end piece and clean out any debris.
Water is dripping from
the spout/vent
intermittently.
• The expansion chamber isn’t
draining properly due to low
water pressure.
• The spout is blocked.
• Unplug the unit. If the dripping doesn’t stop after a few
minutes, check the supply valve to ensure that is fully
open and there are no obstructions in the water line
reducing the pressure below 30 psi (
i.e., a poorly
mounted saddle valve, a clogged water filter, or a
partially opened shut-off valve).
• Unscrew spout end piece and clean out any debris.
Water is dripping
from the spout/vent
constantly.
• Debris in the water line may be
in the faucet valve seat causing a
slow water leak.
• Unscrew spout end piece and clean out any debris.
• Activate faucet lever 7-10 times to flush faucet & lines.
Water discoloration/
rusty appearance.
• Corrosion of unit.
• Unplug and drain unit as described in the Seasonal
Storage/ Drainage Section on page 8 of this manual.
If the water discoloration remains after draining and
refilling unit, discontinue use and contact an
authorized InSinkErator service agent.
PROBLEM
POSSIBLE CAUSE
If you are still experiencing trouble, visit
www.insinkerator.com/foodservice or call 1-800-845-8345.
An instant hot water dispenser, like any water heater, has a limited life and will eventually fail. To avoid
possible property damage, this instant hot water dispenser should be regularly examined for leakage and
replaced when necessary. A drain pan, plumbed to an appropriate drain or outfitted with a leak detector,
should be used in those applications where any leakage could cause property damage.
10