Invacare MA95Z Owners Manual - Page 28

Placing Patient on the Mattress

Get Invacare MA95Z PDF manuals and user guides View all Invacare MA95Z manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

microAIR® MA90 and MA95 Series 5.3 Placing Patient on the Mattress 1. Press the Mode button or Max Inflate button to turn on the control unit to maximum flow. In this mode, the Max Inflate Led lights up. 2. After the mattress is fully inflated, place the patient on the bed. 3. Ensure that the patient's feet are towards the foot end of the mattress (the end with the hose). 4. Center the patient on the bed from side-to-side and head-to-foot. Special positioning may be required with contracted patients to provide comfortable positions. 5. After placing the patient, make certain no objects will fall under the patient, such as feeding tubes, IV's etc. 6. Wait five minutes for the mattress pressure to stabilize. 7. Set the comfort pressure to the desired comfort level. 8. Wait five minutes for the mattress pressure to stabilize. 9. Verify that the patient has not bottomed out by performing the following steps: a. Ensure that the patient is lying flat on his/her back in the middle of the mattress. b. Place four fingers between the air cushions directly underneath the sacral region of the patient's body. c. Ensure that there is 3 to 4-finger width clearance between the bottom of the patient and the bed frame. d. Adjust the comfort setting, if needed. e. Wait five minutes for the mattress pressure to stabilize. f. Repeat Steps A-E until patient has not bottomed out and patient comfort is achieved. 10. If the patient feels that the bed is too soft/hard, press the Soft or Firm button to adjust the comfort settings. 11. Use a regular pillow to help support and stabilize the patient's head. 28 1148139-H

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
microAIR® MA90 and MA95 Series
5.3
Placing Patient on the Mattress
1.
Press the Mode button or Max Inflate button to turn on
the control unit to maximum flow.
In this mode, the Max Inflate Led lights up.
2.
After the mattress is fully inflated, place the patient
on the bed.
3.
Ensure that the patient’s feet are towards the foot end
of the mattress (the end with the hose).
4.
Center the patient on the bed from side-to-side and
head-to-foot.
Special positioning may be required with
contracted patients to provide comfortable
positions.
5.
After placing the patient, make certain no objects will
fall under the patient, such as feeding tubes, IV's etc.
6.
Wait five minutes for the mattress pressure to stabilize.
7.
Set the comfort pressure to the desired comfort level.
8.
Wait five minutes for the mattress pressure to stabilize.
9.
Verify that the patient has not bottomed out by
performing the following steps:
a. Ensure that the patient is lying flat on his/her back in
the middle of the mattress.
b. Place four fingers between the air cushions directly
underneath the sacral region of the patient’s body.
c. Ensure that there is 3 to 4-finger width clearance
between the bottom of the patient and the bed
frame.
d. Adjust the comfort setting, if needed.
e. Wait five minutes for the mattress pressure to
stabilize.
f.
Repeat Steps A-E until patient has not bottomed out
and patient comfort is achieved.
10. If the patient feels that the bed is too soft/hard, press
the Soft or Firm button to adjust the comfort settings.
11. Use a regular pillow to help support and stabilize the
patient's head.
28
1148139-H