JVC GR-D775 Instructions - Page 16

Loading/Unloading A Cassette - battery

Get JVC GR-D775 - GR D775U Camcorder PDF manuals and user guides
UPC - 046838028595
View all JVC GR-D775 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

16 EN GETTING STARTED Loading/Unloading A Cassette The camcorder needs to be powered up to load or eject a cassette. Cassette holder cover PUSH Cassette holder OPEN/ EJECT Erase protection tab Make sure the window side is facing out. 1 Slide and hold OPEN/EJECT in the direction of the arrow, then pull the cassette holder cover open until it locks. The cassette holder opens automatically. ● Do not touch internal components. 2 Insert or remove a tape and press "PUSH" to close the cassette holder. ● Be sure to press only the section labeled "PUSH" to close the cassette holder; touching other parts may cause your finger to get caught in the cassette holder, resulting in injury or product damage. ● Once the cassette holder is closed, it recedes automatically. Wait until it recedes completely before closing the cassette holder cover. ● When the battery pack's charge is low, you may not be able to close the cassette holder cover. Do not apply force. Replace the battery pack with a fully charged one or use AC power before continuing. 3 Close the cassette holder cover firmly until it locks into place. NOTES: ● If you wait a few seconds and the cassette holder does not open, close the cassette holder cover and try again. If the cassette holder still does not open, turn the camcorder off then on again. ● If the tape does not load properly, open the cassette holder cover fully and remove the cassette. A few minutes later, insert it again. ● When the camcorder is suddenly moved from a cold place to a warm environment, wait a short time before opening the cassette holder cover. • Appears if a tape is loaded while the Power Switch is set to "REC". • Blinks when no tape is loaded. TAPE! Appears if a tape is not loaded when the Recording Start/Stop Button or SNAPSHOT Button is pressed while the Power Switch is set to "REC" and the VIDEO/MEMORY Switch is set to "VIDEO". CHECK TAPE'S ERASE PROTECTION TAB Appears when the erase protection tab is set to "SAVE" while the Power Switch is set to "REC" and the VIDEO/MEMORY Switch is set to "VIDEO". (੬ pg. 18)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
GETTING STARTED
16
EN
The camcorder needs to be powered up to
load or eject a cassette.
1
Slide and hold
OPEN/EJECT
in the
direction of the arrow, then pull the cassette
holder cover open until it locks. The cassette
holder opens automatically.
●
Do not touch internal components.
2
Insert or remove a tape and press
“
PUSH
”
to close the cassette holder.
●
Be sure to press only the section labeled
“
PUSH
”
to close the cassette holder; touching
other parts may cause your
fi
nger to get caught
in the cassette holder, resulting in injury or
product damage.
●
Once the cassette holder is closed, it recedes
automatically. Wait until it recedes completely
before closing the cassette holder cover.
●
When the battery pack
’
s charge is low, you may
not be able to close the cassette holder cover.
Do not apply force. Replace the battery pack
with a fully charged one or use AC power before
continuing.
3
Close the cassette holder cover
fi
rmly until
it locks into place.
NOTES:
●
If you wait a few seconds and the cassette
holder does not open, close the cassette holder
cover and try again. If the cassette holder still
does not open, turn the camcorder off then on
again.
●
If the tape does not load properly, open the
cassette holder cover fully and remove the
cassette. A few minutes later, insert it again.
●
When the camcorder is suddenly moved from a
cold place to a warm environment, wait a short
time before opening the cassette holder cover.
•
Appears if a tape is loaded while the Power
Switch is set to
“
REC
”
.
•
Blinks when no tape is loaded.
Appears if a tape is not loaded when the
Recording Start/Stop Button or
SNAPSHOT
Button is pressed while the Power Switch is set to
“
REC
”
and the
VIDEO/MEMORY
Switch is set to
“
VIDEO
”
.
Appears when the erase protection tab is set to
“
SAVE
”
while the Power Switch is set to
“
REC
”
and the
VIDEO/MEMORY
Switch is set to
“
VIDEO
”
. (
±
pg. 18)
Loading/Unloading A Cassette
Make sure the window
side is facing out.
OPEN/
EJECT
PUSH
Cassette holder
Erase
protection
tab
Cassette
holder
cover
TAPE!
CHECK TAPE
’
S ERASE PROTECTION TAB