JVC JY-VS200U JY-VS200U User Manual -- Pages 66-95 (616KB) - Page 7

Insert Editing

Get JVC JY-VS200U - Professional Dv 1-ccd Camcorder PDF manuals and user guides View all JVC JY-VS200U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

72 EN Display 12 : 34 Power Switch USING THE REMOTE CONTROL UNIT (cont.) Insert Editing You can record a new scene into a previously recorded tape, replacing a section of the original recording with 6w minimal picture distortion at the in and outpoints. The original audio remains unchanged. NOTES: ● Before performing the following steps, make sure that "TIME CODE" is set to "ON" in the Menu Screen (੬ pg. 41). ● Insert Editing is not possible on a tape recorded in the LP mode or on a blank portion of a tape. ● To perform Insert Editing while watching in the television, make connections ( ੬ pg. 54). 1 Play back the tape, locate the Edit-Out point and press PAUSE (6). Confirm the time code at this point (੬ pg. 42). 2 Press REW (2) until the Edit-In point is located, then press PAUSE (6). Lock Button 3 Press and hold INSERT (w) on the remote control, then press PAUSE (6). "6w" and the Time Code (min.:sec.) appear and the camcorder enters InsertPause mode. 4 Press START/STOP to begin editing. •Confirm the insert at the time code you checked in step 1. •To pause editing, press START/STOP. Press it again to resume editing. 5 To end Insert Editing, press START/STOP, then STOP (5). REW STOP Remote sensor START/STOP INSERT PLAY PAUSE NOTES: ● Program AE with special effects (੬ pg. 36, 37) can be used to spice up the scenes being edited during Insert Editing. ● During Insert Editing, the date and time information changes. ● If you perform Insert Editing onto a blank space on the tape, the audio and video may be disrupted. Make sure you only edit recorded areas. ● During Insert Editing, when the tape moves to scenes recorded in the LP mode or a blank portion, Insert Edting stops ( ੬ pg. 87). JY-VS200U EN 66-95 72 01.3.12, 7:31 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
72
EN
USING THE REMOTE CONTROL UNIT
(cont.)
PAUSE
START/STOP
INSERT
PLAY
REW
STOP
12:34
6
w
Insert Editing
You can record a new scene into a previously recorded
tape, replacing a section of the original recording with
minimal picture distortion at the in and outpoints. The
original audio remains unchanged.
NOTES:
●
Before performing the following steps, make sure that
“TIME CODE” is set to “ON” in the Menu Screen
(
±
pg. 41).
●
Insert Editing is not possible on a tape recorded in the LP
mode or on a blank portion of a tape.
●
To perform Insert Editing while watching in the
television, make connections (
±
pg. 54).
1
Play back the tape, locate the Edit-Out point and
press
PAUSE
(
6
). Confirm the time code at this point
(
±
pg. 42).
2
Press
REW
(
2
) until the Edit-In point is located, then
press
PAUSE
(
6
).
3
Press and hold
INSERT
(
w
) on the remote control,
then press
PAUSE
(
6
). “
6w
” and the Time Code
(min.:sec.) appear and the camcorder enters Insert-
Pause mode.
4
Press
START/STOP
to begin editing.
•Confirm the insert at the time code you checked in
step
1
.
•To pause editing, press
START/STOP
. Press it again
to resume editing.
5
To end Insert Editing, press
START/STOP
, then
STOP
(
5
).
NOTES:
●
Program AE with special effects (
±
pg. 36, 37) can be
used to spice up the scenes being edited during Insert
Editing.
●
During Insert Editing, the date and time information
changes.
●
If you perform Insert Editing onto a blank space on the
tape, the audio and video may be disrupted. Make sure
you only edit recorded areas.
●
During Insert Editing, when the tape moves to scenes
recorded in the LP mode or a blank portion, Insert Edting
stops (
±
pg. 87).
Power Switch
Lock Button
Display
Remote sensor
JY-VS200U EN 66-95
01.3.12, 7:31 PM
72