JVC SR-V101US Instruction Manual - Page 16
VCR Plus, Timer Programing, Express Timer Programing, 24HR Quick Programing
View all JVC SR-V101US manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 16 highlights
VCR Plus+® Timer Programing The PlusCode programing numbers are the numbers next to the program in most TV listing. Load a cassette with the record safety tab intact. If not, set "REC SAFETY" to "OFF" (੬ pg. 19). The VCR turns on, and the counter is reset, automatically. A Press PROG. on the Remote to access the PlusCode No. screen. PLUSCODE NO. PRESS NUMBER KEY (0-9) PRESS (+/-) TO SET EXPRESS PROGRAMMING PRESS (PROG.) TO END VCR PLUS+ SYSTEM B Press the appropriate Number keys to input the PlusCode number, then press OK or SHUTTLE PLUS e. Check to make sure the setting is accurate on the Program screen. PLUSCODE NO. 12345678 PRESS NUMBER KEY (0-9) THEN (OK) PRESS (PROG.) TO END VCR PLUS+ SYSTEM PROGRAM 1 (PLUSCODE NO. 12345678) START STOP 8:00PM 10:00PM DATE CH 12/24/04 12 SP FRI PRESS (8=DAILY, 9=WEEKLY STOP+/- = STOP TIME, SP/EP) PRESS (PROG.) TO END ● If the Guide Channel Set screen appears after pressing OK, press the Number keys, CH+/- or SHUTTLE PLUS rt to input the number of the GUIDE CHANNEL SET GUIDE CH : 12 VCR CH : - - - channel on which the broadcast for the PlusCode number is received on the VCR, then press OK. PRESS NUMBER KEY (0-9) OR ( , ), THEN (OK) PRESS (PROG.) TO END ● To set the tape speed, press SP/EP. ● To change the stop time, press STOP+/-. ● To timer-record daily (Sunday-Saturday) or weekly serials, press DAILY (Number key "8") or WEEKLY (Number key "9"). Pressing the button again makes the "DAILY" or "WEEKLY" display disappear. ● If you made a mistake, press CANCEL to access the PlusCode No. screen again. ● If an incorrect PlusCode number or the one for a broadcast already finished has been input, "ERROR" is displayed for about 5 seconds, then the PlusCode No. screen reappears. C Press OK or PROG.. ● If "PROGRAM NOT COMPLETED PROGRAM OVERLAP" appears, see "Program Overlap Warning Display" (੬ pg. 17). D Press TIMER. The VCR turns off automatically and "#" is displayed on the display panel. Express Timer Programing Load a cassette with the record safety tab intact. If not, set "REC SAFETY" to "OFF" (੬ pg. 19). The VCR turns on, and the counter is reset, automatically. A Press PROG. on the Remote to access the PlusCode No. screen. B Press START+/- once to access Program screen. Press START+/-, STOP+/-, DATE+/- or CH+/- repeatedly to enter the start PROGRAM 1 START - -:- -AM DATE - -/- -/- - STOP - -:- -AM CH - - - SP time, stop time, date or channel. PRESS (+/-, SP/EP, 8=DAILY ● Press and hold START+/- or STOP+/- 9=WEEKLY), THEN (0K) PRESS (PROG.) TO END to increase the time in 30-minute intervals. ● To set the tape speed, press SP/EP. ● To timer-record daily (Sunday- PROGRAM 1 Saturday) or weekly serials, press DAILY (Number key "8") or WEEKLY (Number key "9"). Pressing the button again makes the "DAILY" or "WEEKLY" display disappear. C Press OK or PROG.. START 8:00AM DATE 12/24/04 FRI STOP 9:00AM CH 110 SP PRESS (+/-, SP/EP, 8=DAILY 9=WEEKLY), THEN (0K) PRESS (PROG.) TO END ● If "PROGRAM NOT COMPLETED PROGRAM OVERLAP" appears, see "Program Overlap Warning Display" (੬ pg. 17). D Press TIMER. The VCR turns off automatically and "#" is displayed on the display panel. 24HR Quick Programing You can program a timer recording that starts within 24 hours using the JOG dial on the VCR. Load a cassette with the record safety tab intact or set "REC SAFETY" to "OFF" (੬ pg. 19). The VCR turns on, and the counter is reset, automatically. A Press 24HR QUICK PROGRAM on the VCR. The start time indicator ( ) starts blinking on the display panel. B Turn the JOG dial to the left or right to set Start time the start time. ● One click stop of the JOG dial changes the time in 5-minute intervals. C Push the JOG dial. The stop time Stop time indicator ( ) starts blinking on the display panel. Turn the JOG dial to the left or right to set the stop time. D Push the JOG dial. Turn the JOG dial to Channel number the left or right to select the channel. ● To set the tape speed, press SP/EP. The current setting for the tape speed appears on the display panel for about 5 seconds. Press SP/EP again to change the setting while tape speed is displayed. E To engage timer recording standby mode, press 24HR QUICK PROGRAM. The VCR turns off automatically and "#" is displayed on the display panel. NOTES: ● If "Err" appears on the display panel, repeat the above steps again. ● When a menu screen is shown, you cannot use 24HR Quick Programing function. Press MENU to return to normal screen, and try again. ● You can use 24HR Quick Programing function also when the VCR is turned off. ● For 24HR Quick Programing function, the program overlap warning display does not appear even if some programs overlap each other. To use the VCR while it is in timer recording standby mode Press TIMER, then press POWER 1. After you use the VCR, press TIMER again to put the VCR into timer recording standby mode. - 16 -