Kenmore 3103 Use and Care Guide - Page 12

Cookware, Operation, A & B, SrnaH

Get Kenmore 3103 - Elite 30 in. Slide-In Gas Range PDF manuals and user guides View all Kenmore 3103 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Setting Surface Controls Setting the Dual Burner (SOME MODELS ONLY) The Dual Burner has two rings of flame that you can control for two different heat levels, one for small and one for large cookware. Large Cookware Operation (Figure 1; Zone A & B) 1. Place a large cooking utensil centered over the surface Burner Grate. 2. Push the surface control knob in and turn counterclockwise out of the OFF position (See Figures 2 & 3). 3. Release the knob and rotate to the UTE position. Note: All electronic surface ignitors will spark at the same time. However, only the dual Burner will ignite. 4. Visually check that zone A & B of dual burner are lit (Figure 4). Adjust the flame size by turning the control knob between the HI and the 2rid dot settings (Figure 3). DO NOT cook with the surface control knob in the LITE position (The electronic ignitor will continue to spark if the knob is left in the LITE position). SrnaH Cookware Operation (Figure 1; Zone A) 1. Place a small cooking utensil centered over the dual surface Burner Grate. 2. Push the surface control knob in and turn counterclockwise out of the OFF position. 3. Release the knob and rotate to the UTE position (Figures 2 & 3). Note: All electronic surface ignitors will spark at the same time. However, only the selected surface Burner will lite. 4. Visually check that zone A & B of the dual burner has lit. 5. Continue to rotate the gas control knob counterclockwise past the 2rid dot setting; zone B flames will extinguish. 6. Visually check that only zone A is lit. 7. Continue to turn the control knob countercmockwise to adjust to the desired flame size for the zone A. Note: The markings between the 2rid dot and Lo settings on the control knob adjust the flame size for the zone A (Refer to Figure 2 or 3). DO NOT cook with any of the surface control knobs in the LITE position (The electronic ignitor will continue to spark if the knob is left in the LITE position). Figure 1 Figure 2 Single Portion of the Dual Burner adjustment area position Dual Portion of the Dual Burner adjustment area Figure 3 Figure 4 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Setting
Surface
Controls
Setting
the
Dual
Burner
(SOME
MODELS
ONLY)
The Dual Burner has two rings of flame that you can control for two different
heat levels, one for small and one for large cookware.
Large
Cookware
Operation
(Figure
1; Zone
A & B)
1. Place a large cooking
utensil centered
over the surface Burner Grate.
2. Push the surface control
knob in and turn counterclockwise
out of the OFF
position
(See Figures 2 & 3).
3. Release the knob and rotate to the UTE position.
Note: All electronic
surface ignitors will spark at the same time. However, only the dual Burner
will ignite.
4. Visually
check that zone A & B of dual burner are lit (Figure 4). Adjust the
flame size by turning the control
knob between
the HI and the 2rid dot
settings
(Figure
3). DO NOT cook with the surface control
knob in the LITE
position
(The electronic
ignitor will continue
to spark if the knob is left in the
LITE position).
SrnaH
Cookware
Operation
(Figure
1; Zone
A)
1. Place a small cooking
utensil centered
over the dual surface Burner Grate.
2. Push the surface control
knob in and turn counterclockwise
out of the OFF
position.
3. Release the knob and rotate to the UTE position
(Figures 2 & 3).
Note: All electronic
surface ignitors will spark at the same time. However,
only the selected
surface Burner will lite.
4. Visually
check that zone A & B of the dual burner has lit.
5. Continue to rotate the gas control knob counterclockwise
past the 2rid dot
setting; zone B flames will extinguish.
6. Visually
check that only zone A is lit.
7. Continue
to turn the control knob countercmockwise
to adjust to the desired
flame size for the zone A. Note: The markings
between the 2rid dot and Lo
settings
on the control
knob adjust the flame size for the zone A (Refer to
Figure 2 or 3). DO NOT cook with any of the surface control knobs in the
LITE position
(The electronic
ignitor will continue
to spark if the knob is left
in the LITE position).
Figure 1
Figure 2
position
Dual Portion
of
the Dual Burner
adjustment
area
Single Portion
of
the
Dual Burner
adjustment
area
Figure
3
Figure 4
12