Kenmore 4542 Installation Instructions - Page 7

Kenmore 4542 - Elite 23.1 cu. Ft. Refrigerator Manual

Get Kenmore 4542 - Elite 23.1 cu. Ft. Refrigerator PDF manuals and user guides View all Kenmore 4542 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

2. Use a sturdy container to depress the water dispenser bar until the water begins to flow. Flush the water system by dispensing and discarding 2 to 3 gal. (8 to 12 L) of water. Cleaning the system will take approximately 5 minutes and will help clear air from the line. Additional flushing may be required in some households. NOTE: As air is cleared from the system, water may spurt out of the dispenser. Open the freezer door and turn on the ice maker. Move the switch to the ON (left) position. See the Use & Care Guide further instructions on the operation of your ice maker. • Allow 24 hours to produce the first batch of ice. • Discard the first three batches of ice produced. Depending on your model, you may want to select the maximum ice feature to increase the production of ice. 3. Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions fire, or electrical shock. can result in death, • IMPORTANT: All four leveling legs must contact the floor to support and stabilize the full weight of the refrigerator. Remove the Base Grille 1. 2. Plug into a grounded 3 prong outlet. Move refrigerator into final position. 1. Open the refrigerator doors to 90 °. 2. Remove base grille. Grasp the grille with both hands. Lift up and tilt the top of the grille toward you. NOTE: Do not remove the Tech Sheets fastened behind the grille. Level the Refrigerator There is a set of two leveling bolts on each side of the refrigerator behind the base grille. The top bolts adjust the rear of the refrigerator, and the bottom bolts adjust the front of the refrigerator. Please read before using the water system. Immediately after installation, follow the steps below to make sure that the water system is properly cleaned. 1. Open the freezer door and turn off the ice maker. The ON/ OFF switch is located on the top right side of the freezer compartment. Move the switch to the OFF (right) setting as shown. JJJJ NOTES: Make sure the base grille filter is properly installed and the cap is in the horizontal position. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts. IJ.J) A Rear leveling bolt (top) B Front leveling bolt (bottom)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
2.
Electrical
Shock
Hazard
Plug into a grounded
3 prong
outlet.
Do
not
remove
ground
prong.
Do
not
use an adapter.
Do
not
use an extension
cord.
Failure
to follow
these instructions
can result
in death,
fire, or electrical
shock.
1.
Plug into a grounded
3 prong
outlet.
2.
Move refrigerator
into final position.
Please read before
using the water
system.
Immediately
after installation,
follow
the steps below to make
sure that the water
system
is properly
cleaned.
1.
Open
the freezer door and turn
off the ice maker. The ON/
OFF switch
is located
on the top
right side of the freezer
compartment.
Move the switch
to the OFF (right) setting
as
shown.
3.
Use a sturdy
container
to depress
the water
dispenser
bar
until the water
begins
to flow.
Flush the water
system
by
dispensing
and discarding
2 to 3 gal. (8 to 12 L) of water.
Cleaning
the system
will take approximately
5 minutes
and
will help clear air from the line. Additional
flushing
may be
required
in some
households.
NOTE:
As air is cleared
from the system,
water
may spurt
out
of the dispenser.
Open
the freezer door and turn
on the ice maker. Move
the
switch
to the ON (left) position.
See the Use & Care Guide
further
instructions
on the operation
of your
ice maker.
•
Allow
24 hours to produce
the first batch
of ice.
•
Discard the first three batches
of ice produced.
•
Depending
on your
model, you may want to select the
maximum
ice feature
to increase the production
of ice.
IMPORTANT:
All four
leveling legs must
contact
the floor
to
support
and stabilize
the full weight
of the refrigerator.
Remove
the Base
Grille
1.
Open
the refrigerator
doors to 90°.
2.
Remove
base grille. Grasp
the grille with
both
hands. Lift up
and tilt the top of the grille toward
you.
NOTE:
Do not remove
the Tech Sheets fastened
behind
the
grille.
Level the
Refrigerator
There is a set of two leveling
bolts on each side of the refrigerator
behind the base grille. The top
bolts adjust
the rear of the
refrigerator,
and the bottom
bolts adjust
the front of the
refrigerator.
JJJJ
NOTES:
Make sure the base grille filter is properly
installed
and the
cap is in the horizontal
position.
Do
not
use
with water
that
is
microbiologically
unsafe
or of unknown
quality
without
adequate
disinfection
before or after the system.
Systems
certified
for cyst
reduction
may be used on disinfected
waters
that
may
contain
filterable
cysts.
IJ.J)
A
Rear leveling
bolt (top)
B Front
leveling
bolt
(bottom)