Kenmore 75051 Owners Manual - Page 10

Energy, Saver, Timer, Speed

Get Kenmore 75051 - 5,300 BTU Single Room Air Conditioner PDF manuals and user guides View all Kenmore 75051 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

DISPLAY REMOTE CONTROL SIGNAL RECEIVER TEMPERATURE SETTING • Use this button to automaticallycontrol the temperature of the room. The temperature can be set within a range of 60°F to 86°F by increments of I°F. V TEMP A _ J I ENERGY SAVER [MODE o_ FAN 0 COOL O TIMER ON/OFF FAN SPEED H I/LO Oi [ [ . The fan stops when the compressorstops cooling. Approximately every 3 minutes the fan will turn on and check the room air to determine if cooling is needed. ENERGY SAVER _- DISPLAY COOL/FAN I |. Everytimeyou push this button, it will toggle between COOL and FAN. |. You will usually use shut-off time while you sleep. • For your seep ng comfort, once T mer s set, the Temperature setting will raise 2°F after 30 min., and once again after another |. 3If0unmitini.s running, Timer sets number of hours until shut-off. • Every time you push Timer button, it advances the Timer setting as follows: ! Hour ) 2 Hours ) etc. !_ 12 Hours maximum. START TIME • If unit is off, Timer sets number of hours before unit starts. • Every time you push Timer button, it advances the Timer setting as folIows: 1 Hour Ip 2 Hours Ip etc. _. 12 Hours maximum. POWER • To turn the air conditioner ON, push the button.To turn the air conditioner OFF, push the button again. • This button takes priority over any other button. • When you first turn it on, the unit is in cool mode, High fan speed, Temperature setting at 72°F. FAN SPEED • Everytimeyou push this button,it advancesthe setting as follows: {High(F2) _. Low(F1) _, High(F2)} In failure of electric power, the unit runs as previous setting operation. -10-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
DISPLAY
REMOTE
CONTROL
SIGNAL
RECEIVER
TEMPERATURE SETTING
•
Use this button to automaticallycontrol the temperature
of the room.
The
temperature
can be set within
a range
of
60°F
to 86°F
by increments
of
I°F.
I
_
ENERGY
SAVER
V
TEMP
A
_
[
[
. The fan stops when the compressorstops cooling.
J
Approximately
every
3 minutes
the fan will turn
on and
check
the
room
air to determine
if cooling
is needed.
ENERGY
o
SAVER
[
MODE
FAN 0
COOL
O
TIMER
ON/OFF
FAN
SPEED
H I/LO
_-
DISPLAY
COOL/FAN
I
|.
Everytimeyou push this button, it will toggle between
COOL
and
FAN.
|.
You will usually
use shut-off
time while
you sleep.
|.
If unit is running,
Timer
sets
number
of hours
until shut-off.
• For your seep
ng comfort,
once T mer s set, the Temperature
O
i
setting
will raise 2°F after 30 min., and once again
after another
30 min.
• Every time you push Timer
button,
it advances
the Timer
setting
as follows:
!
Hour
) 2 Hours
) etc. !_ 12 Hours maximum.
START
TIME
• If unit is off, Timer
sets number
of hours
before
unit starts.
• Every time you push Timer
button,
it advances
the Timer
setting
as folIows:
1 Hour
Ip 2 Hours
Ip etc.
_. 12 Hours
maximum.
POWER
• To turn the air conditioner ON, push the button.To turn the air
conditioner
OFF,
push the
button
again.
• This
button
takes
priority
over
any other
button.
• When
you first turn
it on, the
unit is in cool
mode,
High fan
speed,
Temperature
setting
at 72°F.
FAN SPEED
• Everytimeyou push this button,it advancesthe setting as
follows:
{High(F2)
_. Low(F1)
_, High(F2)}
In failure of electric power, the unit runs as previous
setting operation.
-10-