Kenwood KVT-M707 Instruction Manual - Page 69

The memory is erased when the ignition is - harness

Get Kenwood KVT-M707 PDF manuals and user guides View all Kenwood KVT-M707 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

? No sound can be heard, or the volume is low. ✔ Attenuator is turned on. Turn off Attenuator. ✔ The fader or balance settings are set all the way to one side. Reset the fader and/or balance settings. ✔ The input/output wires or wiring harness are connected incorrectly. Reconnect the input/output wires or the wiring harness correctly. See the section on . ? The sound quality is poor or distorted. ✔ One of the speaker wires is being pinched by a screw in the car. Check the speaker wiring. ✔ The speakers are not wired correctly. Reconnect the speaker wires so that each output terminal is connected to a different speaker. ? Radio reception is poor. ✔ The car antenna is not extended. Pull the antenna out all the way. ✔ The antenna control wire is not connected. Connect the wire correctly, referring to the section on . ? The memory is erased when the ignition is turned off. ✔ The battery wire has not been connected to the proper terminal. Connect the wire correctly, referring to the section on . ✔ The ignition and battery wire are incorrectly connected. Connect the wire correctly, referring to the section on . ? Does not switch to the rear view camera video display when pressing the [V.SEL] button. ✔ The reverse sensor wire is disconnected. Connect the wire correctly, referring to the section on . English | 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
English
|
69
?
No sound can be heard, or the volume is low.
✔
Attenuator is turned on.
Turn off Attenuator.
✔
The fader or balance settings are set all the
way to one side.
Reset the fader and/or balance settings.
✔
The input/output wires or wiring harness are
connected incorrectly.
Reconnect the input/output wires or the
wiring harness correctly. See the section on
<INSTALLATION MANUAL>.
?
The sound quality is poor or distorted.
✔
One of the speaker wires is being pinched by a
screw in the car.
Check the speaker wiring.
✔
The speakers are not wired correctly.
Reconnect the speaker wires so that each
output terminal is connected to a different
speaker.
?
Radio reception is poor.
✔
The car antenna is not extended.
Pull the antenna out all the way.
✔
The antenna control wire is not connected.
Connect the wire correctly, referring to the
section on <INSTALLATION MANUAL>.
?
The memory is erased when the ignition is
turned off.
✔
The battery wire has not been connected to
the proper terminal.
Connect the wire correctly, referring to the
section on <INSTALLATION MANUAL>.
✔
The ignition and battery wire are incorrectly
connected.
Connect the wire correctly, referring to the
section on <INSTALLATION MANUAL>.
?
Does not switch to the rear view camera video
display when pressing the [V.SEL] button.
✔
The reverse sensor wire is disconnected.
Connect the wire correctly, referring to the
section on <INSTALLATION MANUAL>.