Kenwood VR-510 User Manual - Page 23

"SW RE-MIX" scrolls across the display SP A B TI.VOL L R CLIP MUTE SW RDS EON PTY TP TA NEWS FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S.DIRECT MEMO MHz 3 STEREO MONITOR ST. kHz DOWN MIX DSP TUNED 2 Press the SET UP or display operation 2 [Next] key to accept the setting. • The receiver enters the speaker volume level adjustment mode. • In step 4, indications appear only for the selected channels of the speakers that require adjusting. 4 Adjust the speaker volume. From your usual listening position, adjust the volume levels. The volume levels from each speaker should be the same. 1 Use the MULTI CONTROL knob or 5/∞ keys to adjust the volume of the test tone output from the speaker channel to be adjusted. The channel indication blinks while the test tone is being output. SP A B TI.VOL CLIP MUTE RDS EON PTY TP TA NEWS L CR LFE LS S RS FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S.DIRECT MEMO MHz 3 STEREO MONITOR ST. kHz DOWN MIX DSP TUNED The test tone is heard from the speakers in the following sequence for 2 seconds each: = L = C = R = SR = SL = SW • If you change the volume level settings for the speakers while listening to music, the settings referred to on this page are also changed. ∞ • If the speaker setting selects are OFF, the speaker level settings are reset. 2 Press the SET UP or display operation 2 [Next] key. • The test tone is turned off. The receiver enters the mode for inputing the bass peak level and the current peak level will be shown. • To obtain accurate output levels, it is recommended to use a handheld Sound Pressure Level (SPL) meter. Readings should be taken from your actual listening position and adjust the level of each speaker to 75dB SPL (C-weighted/ slow meter mode). 5 Adjust the bass peak level. A restriction is put on the low frequency so that the bass peak level will not go higher than the acceptable level when the volume is increased. If subwoofer speaker is OFF, the limitation will affect the low frequency of the front left and right speakers. SP A B TI.VOL CLIP MUTE RDS EON PTY TP TA NEWS L CR LFE SW LS S RS FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S.DIRECT MEMO MHz 3 STEREO MONITOR ST. kHz DOWN MIX DSP TUNED 1 Use the MULTI CONTROL knob or 5/∞ keys to adjust the bass peak level to -30. • The bass peak level may be adjusted from - 30dB to 0dB and OFF. • When no subwoofer is in use, the test tone will be output from the front channel speakers. 2 To find the bass peak level limit, keep increasing the bass peak level by using the MULTI CONTROL knob or 5/∞ keys while test tone is being output until the clip point of the subwoofer is found. SP A B TI.VOL CLIP MUTE RDS EON PTY TP TA NEWS LFE SW LS S RS FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S.DIRECT MEMO MHz 3 STEREO MONITOR ST. kHz DOWN MIX DSP TUNED 3 Press the SET UP or display operation 2 [Next] key. • The receiver enters the mode for inputting the distance to the speakers. Preparing for surround sound 6 Input the distance to the speakers. 23 1 Measure the distance from the listening position to each of the speakers. Jot down the distance to each of the speakers. Distance to front left speaker : ____ feet (meters) Distance to center speaker : ____ feet (meters) Distance to front right speaker : ____ feet (meters) Distance to surround right speaker : ____ feet (meters) Distance to surround left speaker : ____ feet (meters) Distance to subwoofer : ____ feet (meters) Preparations 2 Use the MULTI CONTROL knob or 5/∞ keys to select the distance to the front speakers. The speaker indicator to be adjusted blinks. SP A B TI.VOL CLIP MUTE RDS EON PTY TP TA NEWS LC LFE SW LS S RS FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S.DIRECT MEMO MHz 3 STEREO MONITOR ST. kHz DOWN MIX DSP TUNED Indication in feet Indication in meters • The allowable setting range is 1 to 30 feet (0.3 to 9.0 m), adjustable in 1 foot (0.3 m) increment. 3 Press the SET UP or display operation 2 [Next] key. 4 Repeat steps 2 and 3 to input the distance for each of the speakers. 5 Setup is complete when the input indication reappears. SP A B TI.VOL CLIP MUTE RDS EON PTY TP TA NEWS L CR LFE SW LS S RS Display when all speakers have been selected. • The speakers you have selected should appear on the display. Confirm that all the speakers have been correctly selected. Input level adjustment (analog sources only) If the input level of an analog source signal is too high, the CLIP indicator will blink. Adjust the input level. CLIP RDS TP 1 Use the INPUT SELECTOR knob to select the source which you want to adjust. • You can store a separate input level for each input source. If the MONITOR function is ON, you can store an input level for when MONITOR is on independently of the input levels for the input sources. 2 Press the SOUND key repeatedly until the "INPUT" indication appears. 3 Use the MULTI CONTROL knob or 5/∞ keys to adjust the input level. SP A B TI.VOL CLIP MUTE RDS EON PTY TP TA NEWS L CR LFE SSWW LS S RS FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S.DIRECT MEMO MHz 3 STEREO MONITOR ST. kHz DOWN MIX DSP TUNED • The adjustment mode is displayed for approximately eight seconds. • The input level may be adjusted to any one of three settings:0dB, -3dB, and -6dB. (The initial setting is 0dB.) 4 Press the SOUND key again to return to the input indication.