Kyocera FS-1120D FS-1120D/1320D Printer Driver Users Guide Rev-12.6 - Page 37

Gutter, Creating a Gutter

Get Kyocera FS-1120D PDF manuals and user guides View all Kyocera FS-1120D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Gutter Layout 1 In the Layout tab, select Scaling. 2 Type or select a percentage between 20 to 500. Scaling adjusts proportionately the height and width of the page. A lower percentage reduces the page and a higher percentage enlarges the page. 3 Click OK to return to the Print dialog box. 4 Click OK to begin printing. A gutter creates additional blank space on the left side and at the top of the sheet. It is often used for binding, hole punch or stapling to make a print job easier to read. Increasing the measurements in Gutter increases the margins around your text and graphics on the left side, or top of the printed sheet. This creates a larger margin space by shifting the printable area to the right, or down as much as one inch (25.4 mm). Creating a Gutter To create a gutter, follow these steps. 1 In the Layout tab, click Gutter. 2 In the Gutter width options, type a value between 0.20 to 1.00 inches (5.0 to 25.4 mm). Long edge (left) This selection modifies the outside margin on the left-side of the page. Short edge (top) This selection modifies the outside margin on the top-edge of the page. Note: Availability of Gutter settings varies depending on Orientation and Duplex mode settings in the Basic tab. 3 If text extends too close to the edge of the page, select Reduce image to fit. The text appears slightly reduced and away from the edge of the page. If text does not extend beyond the page when the gutter increases, clear Reduce image to fit. 4 Click OK to save gutter settings, then click OK again to return to the Print dialog box. 5 Click OK to begin printing. KX DRIVER 5-4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Layout
1
In the
Layout
tab, select
Scaling
.
2
Type or select a percentage between 20 to 500.
Scaling
adjusts proportionately the height and width of the page. A lower
percentage reduces the page and a higher percentage enlarges the page.
3
Click
OK
to return to the
Print
dialog box.
4
Click
OK
to begin printing.
Gutter
A gutter creates additional blank space on the left side and at the top of the
sheet. It is often used for binding, hole punch or stapling to make a print job
easier to read. Increasing the measurements in
Gutter
increases the margins
around your text and graphics on the left side, or top of the printed sheet. This
creates a larger margin space by shifting the printable area to the right, or down
as much as one inch (25.4 mm).
Creating a Gutter
To create a gutter, follow these steps.
1
In the
Layout
tab, click
Gutter
.
2
In the
Gutter width
options, type a value between 0.20 to 1.00 inches (5.0 to
25.4 mm).
Long edge (left)
This selection modifies the outside margin on the left-side of the page.
Short edge (top)
This selection modifies the outside margin on the top-edge of the page.
Note:
Availability of
Gutter
settings varies depending on
Orientation
and
Duplex mode
settings in the
Basic
tab.
3
If text extends too close to the edge of the page, select
Reduce image to fit
.
The text appears slightly reduced and away from the edge of the page. If text
does not extend beyond the page when the gutter increases, clear
Reduce
image to fit
.
4
Click
OK
to save gutter settings, then click
OK
again to return to the
Print
dialog
box.
5
Click
OK
to begin printing.
KX DRIVER
5-4