LG 60PC1D Owners Manual - Page 57

These functions are available in 42PC3D/3DC/3DV, 50PC3D, 60PC1D/1DC models only. 18. ISM Method (Command2:p) G To avoid having a fixed image remain on screen. Transmission [ j ][p][ ][Set ID][ ][Data][Cr] Data 1: Inversion 2: Orbiter 4: White Wash 8: Normal Acknowledgement [p][ ][Set ID][ ][OK][Data][x] 19. Low Power (Command2:q) G To control the Low Power function on/off. You can also adjust Low Power in Option menu. Transmission [ j ][q][ ][Set ID][ ][Data][Cr] Data 0: Low Power off 1: Low Power on Acknowledgement [q][ ][Set ID][ ][OK][Data][x] Reference 20. Tune Command (Command: m a) G To tune channel to following physical/major/minor number Transmission [m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][ ][Data3][ ][Data4][ ][Data5][Cr] Data 0: Physical Channel Number(Transmit by Hexadecimal code) NTSC air:02~45 NTSC cable: 01~87 ATSC air:02~45 ATSC cable:01~87 Data 1,Data 2: Major Channel Number(two part) or Channel Number(One part) Data1: High byte Data2: Low byte Two part channel number: Major number-Minor number One part channel number: If the channel band is ATSC digital cable, it can be used. In case of using one part channel number, minor channel does not need. Data 3, Data 4: Minor Channel Number Data3: High byte Data4: Low byte Data 5: Main 7 Picture 0 Main 1 Two/One Using 4 6 Part Channel 5 Physical Reserv Channel ed 3 2 1 0 Two 0 Use x 0 00 1 One 1 No Use x 0 00 x 0 01 x 0 01 x 0 10 x 0 10 x 0 11 x 0 11 0 Step 0 NTSC Air 1 NTSC Cable 0 ATSC Air 1 ATSC Cable_std 0 ATSC Cable_hrc 1 ATSC Cable_irc 0 ATSC cable_auto 1 Reserved x xx xx ... x 1 1 1 1 Reserved * All data are transmitted by Hexadecimal code *Two/One part Channel: 6th bit This bit is used in a cable-ready system. *Using physical channel: 5th bit If the channel band is NTSC air or NTSC cable, channel tuning can be done by only physical channel. In this case, using physical channel bit must be low(0). But if the channel band is ATSC air or ATSC cable, there are two cases that physical channel enable or disable. If the physical channel sending is meaningful, you should set this bit low(0). If the physical channel sending is meaningless, you should set this bit high(1). Example) 1. Analog channel: NTSC cable, channel number(35), main pic- ture Command: ma 00 23 xx xx xx xx 01attribute(0x01): main picture, two part(it's not mandatory), using physical channel, NTSC cable 'xx' data: don't care major and minor channel number in case analog channel tuning. 2. Digital channel: ATSC air, channel number(don't know physical channel, major(30), minor(3)), main picture Command: ma 00 xx 00 1E 00 03 22 attribute(0x22): main picture, two part, not using physical channel, ATSC air 'xx' data: don't care analog channel number in case digital channel tuning. 3. Digital channel: ATSC air, channel number (physical(20), major (30), minor (5)), main picture Command: ma 00 14 00 1E 00 05 02 attribute(0x02): main picture, two part, using physical channel, ATSC air. Acknowledgement [a][ ][Set ID][ ][OK][Data0][Data1][Data2][Data3][Data4][Data5][x] [a][ ][Set ID][ ][NG][Data0][x] 57