Home » Lenovo Manuals » Desktops » Lenovo ThinkCentre M55 » Manual Viewer

Lenovo ThinkCentre M55 Hardware Maintenance Manual - Page 70

Audio port Interface Test Passed

View all Lenovo ThinkCentre M55 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

Diagnostic Error Code 030-197-XXX SCSI interface test warning 030-198-XXX SCSI interface test aborted 030-199-XXX SCSI interface test failed, cause unknown 035-000-XXX RAID interface Test Passed 035-0XX-XXX RAID interface Failure 035-195-XXX RAID interface Test aborted by user 035-196-XXX RAID interface test halt, error threshold exceeded 035-197-XXX RAID interface test warning 035-198-XXX RAID interface test aborted 035-199-XXX RAID interface test failed, cause unknown 071-000-XXX Audio port Interface Test Passed FRU/Action 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6 "Diagnostics, Test and Recovery Information" on page 47 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6 "Diagnostics, Test and Recovery Information" on page 47 2. Flash the system and re-test. See "Flash update procedures" on page 375 3. Go to "Undetermined problems" on page 76 1. Go to "Undetermined problems" on page 76 2. Flash the system and re-test. See "Flash update procedures" on page 375 3. Replace component under function test No action 1. RAID signal cable 2. RAID device 3. RAID adapter card, if installed 4. System board Information only Re-start the test, if necessary 1. Press F3 to review the log file 2. Re-start the test to reset the log file 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6 "Diagnostics, Test and Recovery Information" on page 47 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6 "Diagnostics, Test and Recovery Information" on page 47 2. Flash the system and re-test. See "Flash update procedures" on page 375 3. Go to "Undetermined problems" on page 76 1. See "Undetermined problems" on page 76 2. Flash the system and re-test. See "Flash update procedures" on page 375 3. Replace component under function test No action 64 Hardware Maintenance Manual

Section	Page
Chapter 1. About this manual	7
Important Safety Information	7
Strategy for replacing FRUs for CTO, CMV, and GAV products	8
Product definition	8
FRU Identification for CTO, CMV, and GAV products	8
Important information about replacing RoHS compliant FRUs	9
Chapter 2. Safety information	11
General safety	11
Electrical safety	11
Safety inspection guide	13
Handling electrostatic discharge-sensitive devices	13
Grounding requirements	14
Safety notices (multi-lingual translations)	14
Chapter 3. General information	37
The ThinkVantage™ Productivity Center program	37
Additional information resources	37
Physical specifications	37
Types 8009, 8791, 8795, 8799, 8803, and 8807	37
Types 6488, 8010, 8792, 8796, 8800, 8804, 8808, and 9168	38
Types 8011, 8793, 8797, 8801, 8805, 8810, and 9166	39
Types 6487, 8012, 8794, 8798, 8802, 8806, 8811, and 9167	40
Chapter 4. General Checkout	43
Problem determination tips	44
Chapter 5. Diagnostics	47
PC-Doctor for Windows	47
PC-Doctor for DOS	47
Creating a diagnostic CD image	47
Creating diagnostic diskettes	48
Running diagnostics from the CD or diskettes	48
Running diagnostics from the Rescue and Recovery workspace	48
PC-Doctor for Windows PE	49
Running diagnostics from the Rescue and Recovery workspace	49
Navigating through the diagnostics programs	49
Running tests	49
Test results	50
Fixed disk advanced test (FDAT)	50
Quick and Full erase - hard drive	52
Viewing the test log	52
Chapter 6. Using the Setup Utility	53
Starting the Setup Utility program	53
Viewing and changing settings	53
Exiting from the Setup Utility program	53
Using passwords	53
User Password	53
Administrator Password	54
Setting, changing, and deleting a password	54
Selecting a startup device	54
Selecting a temporary startup device	54
Changing the startup device sequence	54
Advanced settings	55
Chapter 7. Symptom-to-FRU Index	57
Hard disk drive boot error	57
Power Supply Errors	57
Diagnostic error codes	58
Beep symptoms	76
No-beep symptoms	78
POST error codes	78
Miscellaneous error messages	80
Undetermined problems	82
Chapter 8. FRU lists	85
Machine Type 6487	85
Machine Type 6488	96
Machine Type 8009	106
Machine Type 8010	116
Machine Type 8011	120
Machine Type 8012	129
Machine Type 8791	141
Machine Type 8792	151
Machine Type 8793	161
Machine Type 8794	171
Machine Type 8795	181
Machine Type 8796	190
Machine Type 8797	200
Machine Type 8798	209
Machine Type 8799	219
Machine Type 8800	231
Machine Type 8801	243
Machine Type 8802	254
Machine Type 8803	265
Machine Type 8804	277
Machine Type 8805	286
Machine Type 8806	296
Machine Type 8807	305
Machine Type 8808	318
Machine Type 8810	335
Machine Type 8811	349
Machine Type 9166	368
Machine Type 9167	372
Machine Type 9168	376
Chapter 9. Additional Service Information	381
Security features	381
Hardware controlled Passwords	381
Operating system password	381
Vital product data	381
BIOS levels	381
Flash update procedures	381
Updating (flashing) BIOS from a diskette or CD-ROM	382
Updating (flashing) BIOS from your operating system	382
Recovering from a POST/BIOS update failure	382
Power management	383
Automatic configuration and power interface (ACPI) BIOS	383
Automatic Power-On features	383
Recovering software using the Rescue and Recovery program	383
Appendix A. Notices	385
Television output notice	386

Match case Limit results 1 per page

Diagnostic Error Code

FRU/Action

030-197-XXX

SCSI interface test warning

Make sure the component that is called out

is connected and/or enabled. See Chapter 6

“Diagnostics, Test and Recovery Information” on

page 47

Re-run test

Replace the component that is called out in warning

statement

Replace the component under test

030-198-XXX

SCSI interface test aborted

If a component is called out, make sure it is

connected and/or enabled. See Chapter 6

“Diagnostics, Test and Recovery Information” on

page 47

Flash the system and re-test. See “Flash update

procedures” on page 375

Go to “Undetermined problems” on page 76

030-199-XXX

SCSI interface test failed, cause unknown

Go to “Undetermined problems” on page 76

Flash the system and re-test. See “Flash update

procedures” on page 375

Replace component under function test

035-000-XXX

RAID interface Test Passed

No action

035-0XX-XXX

RAID interface Failure

RAID signal cable

RAID device

RAID adapter card, if installed

System board

035-195-XXX

RAID interface Test aborted by user

Information only

Re-start the test, if necessary

035-196-XXX

RAID interface test halt, error threshold

exceeded

Press F3 to review the log ﬁle

Re-start the test to reset the log ﬁle

035-197-XXX

RAID interface test warning

Make sure the component that is called out

is connected and/or enabled. See Chapter 6

“Diagnostics, Test and Recovery Information” on

page 47

Re-run test

Replace the component that is called out in warning

statement

Replace the component under test

035-198-XXX

RAID interface test aborted

If a component is called out, make sure it is

connected and/or enabled. See Chapter 6

“Diagnostics, Test and Recovery Information” on

page 47

Flash the system and re-test. See “Flash update

procedures” on page 375

Go to “Undetermined problems” on page 76

035-199-XXX

RAID interface test failed, cause unknown

See “Undetermined problems” on page 76

Flash the system and re-test. See “Flash update

procedures” on page 375

Replace component under function test

071-000-XXX

Audio port Interface Test Passed

No action

Hardware Maintenance Manual