Magnavox AJ3720 User manual, English (US) - Page 6

Controls, Installation

Get Magnavox AJ3720 PDF manuals and user guides View all Magnavox AJ3720 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

English CONTROLS TOP, FRONT and SIDE PANEL 1 REPEAT ALARM/TIME DATE: - To switch off the alarm for a 9 minute period. - To display/adjust the date (month and day) and the year - To resume clock time display 2 DISPLAY: To show the status of the set 3 PRESET 1-5: - To select a preset radio station - To select a preset radio alarm 4 ALARM RESET/RADIO OFF: - To stop the active alarm for 24 hours - To switch off alarm 1 or 2 completely - To switch off the radio 5 SLUMBER/BUZZER - To adjust the slumber time on/off - To select the buzzer mode for alarm 1 or 2 6 RADIO ON - To switch on the radio - To go to radio display for 10 seconds - To select the radio mode for alarm 1 or 2 7 BAND: To select the waveband INSTALLATION 8 ALARM 1:To set, review or switch off alarm 1 ALARM 2: To set, review or switch off alarm 2 9 VOLUME: To adjust the radio sound level 0 TUNING / ∞ or § (up or down) - To tune to radio stations automatically or manually - To adjust the clock time, alarm time, date, year ! p: 3.5 mm headphone jack @ WEEKEND SLEEPER - To activate or deactivate the weekend sleeper for alarm 1 or 2 # SET: - To confirm preset stations stored - To activate the setting mode for clock time $ BRIGHTNESS CONTROL: To change the brightness of the display illumination % Pigtail: For FM reception ^ MAINS: for connecting the set to the power supply POWER CONNECTION 1. Check if the power voltage as shown on the type plate (on the bottom of the set) corresponds to your local power voltage. If it does not, consult your dealer or service organisation. ™ If your set is equipped with a voltage selector, found on the bottom right-hand corner of the set, adjust the selector to correspond with your local power. 2. Connect the power plug to the wall outlet. - The AC power supply is now switched on and the numbers on the display will start to flash. You will need to set the correct time. 3. To switch off the AC power supply completely, pull the power plug out of the wall outlet. ALM 1 SUN MON TUE WED THUR FRI SAT AM ZZ PM SLUMBER P1 P2 P3 P4 P5 ALM 2 MW FM MHz kHz ZZ 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
CONTROLS
INSTALLATION
6
English
1.
Check if the power voltage as shown on the type plate (on the
bottom of the set) corresponds to your local power voltage. If
it does not, consult your dealer or service organisation.
™
If your set is equipped with a voltage selector, found on the
bottom right-hand corner of the set, adjust the selector to
correspond with your local power.
2.
Connect the power plug to the wall outlet.
–
The AC power supply is now switched on and the numbers
on the display will start to flash. You will need to set the
correct time.
3.
To switch off the AC power supply completely, pull the power
plug out of the wall outlet.
POWER CONNECTION
1
REPEAT ALARM/
TIME DATE
:
–
To switch off the alarm for a 9 minute
period.
–
To display/adjust the date (month and day)
and the year
–
To resume clock time display
2
DISPLAY:
To show the status of the set
3
PRESET 1-5:
–
To select a preset radio station
–
To select a preset radio alarm
4
ALARM RESET/RADIO OFF:
–
To stop the active alarm for 24 hours
–
To switch off alarm 1 or 2 completely
–
To switch off the radio
5
SLUMBER/BUZZER
–
To adjust the slumber time on/off
–
To select the buzzer mode for alarm 1 or 2
6
RADIO ON
–
To switch on the radio
–
To go to radio display for 10 seconds
–
To select the radio mode for alarm 1 or 2
7
BAND:
To select the waveband
8
ALARM 1
:To set, review or switch off alarm 1
ALARM 2:
To set, review or switch off alarm 2
9
VOLUME:
To adjust the radio sound level
0
TUNING /
∞
or
§
(up or down)
–
To tune to radio stations automatically or
manually
–
To adjust the clock time, alarm time, date,
year
!
p
: 3.5 mm headphone jack
@
WEEKEND SLEEPER
–
To activate or deactivate the weekend
sleeper for alarm 1 or 2
#
SET:
–
To confirm preset stations stored
–
To activate the setting mode for clock time
$
BRIGHTNESS CONTROL:
To change the
brightness of the display illumination
%
Pigtail:
For FM reception
^
MAINS:
for connecting the set to the power
supply
TOP, FRONT and SIDE PANEL
SLUMBER
SUN MON TUE WED THUR FRI SAT
ALM 2
ALM 1
MW
FM
MHz
Z
Z
Z
Z
kHz
AM
PM
P1
P2 P3
P4
P5