Marantz RC2000MKII User Guide - Page 17
To clone duplicate ALL of the memory, contents of one RC2000 Mk, into another, RC2000 Mk, please
View all Marantz RC2000MKII manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 17 highlights
To "clone" (duplicate) ALL of the memory contents of one RC2000 Mk w into another RC2000 Mk w, please follow these steps: 1. Place the source RC2000 Mk w (the one with all of the customized commands, names, macros, macro sequences, and the like) with its infrared transmitter window @3 facing the infrared sensor @4 of another "fresh" RC2000 Mk w (5 cm, or 2 inches apart). Transmitting RC2000 Mkw Receiving RC2000 Mkw MACRO 1 TUNER CH 123 456 CD TAPE 789 OSD GUIDE MUTE M0C 2 D1 D2 D3 D4 DSS MD ON POWER SOURCE ON/OFF CLONE MACRO MODE LEARNING REMOTE CONTROL RC2000MK TV LD AUX OK OFF 4 RC-5 LEARN USE NAME D5 D6 D7 D8 DVD AMP VOL VCR MACRO 3 Approx. 5 cm (2 inches) 2. Press the CLONE button e of the source RC2000 Mk w with a paper clip tip, and select "CLONE TX" (clone transmit) mode (see Figure 17). POWER SOURCE ON ON/OFF OFF CLONE MACRO MODE Press the CLONE button. 3. Press the CLONE button e of the learning (receiving) RC2000 Mk w with the tip of a paper clip or a similar object, and select "CLONE RX" (clone receive mode). Then press the PLAY button !5. Figure 17 POWER SOURCE ON ON/OFF OFF CLONE MACRO MODE Press the CLONE button. Figure 18 4. Press the source RC2000 Mk w's transport control PLAY !5 key to begin the infrared data transmission sequence. Now the "LEARN" indicator of receiving RC2000 Mk w starts to blink. TUNER CD TAPE AUX AMP CH VOL Press the PLAY button. 33 During the transmission, the LCD windows of both RC2000 Mk w remote controls will show a bar-type indicator, moving from left to right during the transmission process. After all bars are lit up on both displays, "TX OK" (transmission OK) will appear in the source RC2000 Mk w's LCD window, and "RX OK" (reception OK) will appear in the "cloned" RC2000 Mk w's LCD window, confirming the end of the copying process (see Figures 19 and 20). LEARN Figure 19 Figure 20 If the audible beep indicator is on, it will sound to let you know that cloning is complete. ¼ Please be sure that, during the copying process, neither RC2000 Mk w is physically disturbed (ideally, they should be placed on a table or other surface, and not hand-held during the copying process). If, for some reason, the copying process was interrupted, the "clone" RC2000 Mk w's LCD display window will indicate "RX NG" (reception no good). Simply begin the clone process anew by repeating the above steps. 5. If the source RC2000 Mk w's memory contents are at or near full capacity, the copying process will take about 3 minutes. After completion of the copying (cloning) process, press the CLONE button on both RC2000 Mk w's with the paper clip tip, and select the OFF mode. Then, you'll have two identically programmed RC2000 Mk w remotes, one of which can again be used as your system's primary remote control, and you'll have the added confidence of knowing that in the event of inadvertent programming (or memory contents being cleared somehow), you can simply retrieve the "backup" RC2000 Mk w that you've safely tucked away, and within minutes restore the programming contents of the original RC2000 Mk w with your customized configuration. POWER SOURCE ON ON/OFF OFF CLONE MACRO MODE LEARNING REMOTE CONTROL Press on both the receiving and transmitting units. 34