Maytag MGDE300VF Use and Care Guide - Page 18

When

using

Air

Only

•

Check

that

coverings

are securely

stitched.

•

Shake

and

fluff

pillows

by hand

periodically

during

the

cycle.

•

Dry

item

completely.

Foam

rubber

pillows

are slow

to dry.

NOTE:

Sensor

Cycles

are not available

when

using

the

Air

Only

setting.

q

To

stop

your

dryer

at

any

time

Press POWER/CANCEl.

once

or open

the

door.

To

pause the dryer at any time

Open

the

door

or press START/PAUSE

once.

To

restart

the

dryer

Close

the

door

and

press and

hold

START/PAUSE

button

until

dryer

starts.

NOTE:

Drying

will

continue

from

where

the

cycle

was

interrupted,

if you

dose

the

door

and

press Start within

5 minutes.

If the cycle

is interrupted

for more

than

5 minutes,

the dryer

will

shut

off.

Select

new

cycle

settings

before

restarting

the dryer.

C,ent 'e

LH:L

This feature

allows

you to

lock your

settings

to avoid

unintended

use of the

dryer.

You can also

use the Control

I.ock

feature

to avoid

unintended

cycle

or option

changes

during

dryer

operation.

To

enable

the

Control

Lock

feature

when

dryer

is running:

Press and

hold

the

CONTROl_

I_OCK button

for 3 seconds.

The control

is locked

when

a

single

beep

is heard

and

the Control

I.ock

light

is on.

•

When

the

dryer

is off,

it is not

necessary

to press the

Control

On

button

before

activating

the

Control

I.ock

feature.

To unlock:

Pressand hold the CONTROl.

I.OCK button for 3 seconds to turn this feature off.

NOTE:

When

the

dryer

is running

and Control

Lock

is on,

the

dryer

can

be stopped

by

pressing

the

POWER/CANCEl.

or START/PAUSE

buttons,

but

cannot

be restarted

until

the

control

is unlocked.

Select

the correct

cycle

and

dryness

level

or temperature

for your

load.

If a Sensor Cycle

is

running,

the

display

shows

the estimated

cycle

time

when

your

dryer

is automatically

sensing

the

dryness

level

of your

load.

If a Timed

Cycle

is running,

the display

shows

the

exact

number

of minutes

remaining

in the

cycle.

Cool

Down

tumbles

the

load without

heat

during

the

last few

minutes

of

all cycles.

Cool

Down

makes

the

loads

easier

to handle

and

reduces

wrinkling.

The

length

of

the Cool

Down

depends

on

the

load

size and

dryness

level.

Drying

tips

•

Follow

care

[abe[ directions

when

they

are available.

If desired,

add

a fabric

softener

sheet.

Follow

package

instructions.

Remove

the

load

from

the

dryer

as soon

as tumbling

stops to

reduce

wrinkling.

This is

especially

important

for

permanent

press, knits

and

synthetic

fabrics.

Avoid drying

heavy work clothes with

lighter fabrics. This could

cause overdrying

of

lighter fabrics,

leading to increased shrinking

or wrinkling.

If you dry sheets in a mixed load or large items, rearrange the load when the signal

sounds. This will

aid in the drying process.

Cycle

tips

•

Dry most loads using the preset cycle settings.

•

Refer to the

Sensor or Timed

Preset Cycle

Settings

chart

(in the

"Cycles"

section)

for

a

guide

to

drying

various

loads.

•

Drying

temperature

and

Sensor

Cycles

Dryness

are preset

when

you

choose

a Sensor

Cycle.

You can

choose

a different

dryness

level,

depending

on

your

load

by pressing

the

SENSOR

CYCI.ES

DRYNESS

button

to select

More

Dry,

Normal,

or I.ess Dry.

•

If you

wish

to

adjust

the cycle

length

of

a Timed

Cycle,

you

must

press the TIME

ADJUST

up or down

buttons.

Adjust

the temperature

of a Timed

Cycle

by pressing

TIMED

CYCI.ES TEMP

until

the

desired

temperature

is selected.

NOTE:

You cannot

choose

a Sensor

Cycles

Dryness

with

Timed

Cycles.

18

Maytag MGDE300VF Use and Care Guide - Page 18

C,ent 'e

Page 18 highlights