Maytag MMV4205BAQ Installation Instructions - Page 20

against, cabinet

Get Maytag MMV4205BAQ - 2.0 cu. Ft. Microwave PDF manuals and user guides View all Maytag MMV4205BAQ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Installation Instructions 6. Place the blower unit back into the opening. C5. MOUNT THE MICROWAVE OVEN End B End A CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched. NOTE: The blower unit exhaust openings should match exhaust openings on rear of microwave oven. 7, Secure screw. the blower unit to the microwave Blower-Plate with the Back of Microwave f _ From the Mounting Plate screw 8, Attach the exhaust adaptor to the rear of the oven by sliding it into the guides at the top center of the back of the oven. Adaptor Back of i_ icrowave _ Guide Guide From Blower motor screw (after attached the exhaust adaptor) Push in securely until it is in the lower locking tabs. Take care to assure that the damper hinge is installed so that it is at the top and that the damper swings freely. FOR EASIER INSTALLATION SAFETY, WE RECOMMEND INSTALL THIS MICROWAVE AND PERSONAL THAT TWO PEOPLE OVEN. IMPORTANT: Do not grip or use handle during installation. NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord. NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf. IMPORTANT: If filler blocks are not used, case damage may occur from over tightening screws. NOTE: When mounting the microwave oven, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps 1-3. Do not pinch cord or lift oven by pulling cord. 1, Lift microwave, tilt it forward, and hook slots at back bottom edge onto four lower tabs of mounting plate. oven up against cabinet bottom 3, Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet. 2O

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Installation
Instructions
6.
Place
the blower
unit back
into the opening.
End A
End B
CAUTION:
Do not pull or stretch
the blower
unit
wiring.
Make
sure
the wires
are not pinched.
NOTE:
The
blower
unit
exhaust
openings
should
match
exhaust
openings
on
rear
of microwave
oven.
7,
Secure
the blower
unit to the microwave
with
the
screw.
Blower-Plate
f
_
From the Mounting
Back of
Microwave
Plate screw
8,
Attach
the exhaust
adaptor
to the rear of the oven
by sliding
it into the guides
at the top center
of the
back
of the oven.
Adaptor
Back of
i_
icrowave
_
Guide
Guide
From
Blower
motor
screw
(after
attached
the
exhaust
adaptor)
Push
in securely
until
it is in the lower
locking
tabs.
Take
care to assure
that the damper
hinge
is installed
so that it is at the top and that
the damper
swings
freely.
C5.
MOUNT
THE MICROWAVE
OVEN
FOR
EASIER
INSTALLATION
AND
PERSONAL
SAFETY,
WE
RECOMMEND
THAT
TWO
PEOPLE
INSTALL
THIS
MICROWAVE
OVEN.
IMPORTANT:
Do
not
grip
or
use
handle
during
installation.
NOTE:
If your
cabinet
is metal,
use the nylon
grommet
around
the power
cord
hole
to prevent
cutting
of the cord.
NOTE:
We recommend
using
filler
blocks
if the
cabinet
front
hangs
below
the cabinet
bottom
shelf.
IMPORTANT:
If
filler
blocks
are
not used,
case
damage
may
occur
from
over
tightening
screws.
NOTE:
When
mounting
the microwave
oven,
thread
power
cord
through
hole
in bottom
of top cabinet.
Keep
it tight
throughout
Steps
1-3.
Do not pinch
cord
or lift oven
by pulling
cord.
1,
Lift microwave,
tilt it
forward,
and
hook
slots
at back
bottom
edge
onto four
lower
tabs
of
mounting
plate.
oven
up
against
cabinet
bottom
3,
Insert
a self-aligning
screw
through
top center
cabinet
hole.
Temporarily
secure
the oven
by
turning
the screw
at least two
full
turns
after
the
threads
have engaged.
(It will be completely
tightened
later.)
Be sure
to keep
power
cord
tight.
Be careful
not
to
pinch
the
cord,
especially
when
mounting
flush
to
bottom
of
cabinet.
2O