Netgear GS108T GS108T Setup Manual - Page 17

Additional Utilities, Managing System Settings, Setup on Introduction to

Get Netgear GS108T - ProSafe - Gigabit Smart Switch PDF manuals and user guides
UPC - 606449051377
View all Netgear GS108T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

GS108T Smart Switch Software Administration Manual If you are starting with an "out of the box" switch and are not using the SmartWizard Discovery utility, you must initially configure your host PC to be on a network segment to match the default parameters of the switch, which are: • IP address: 192.168.0.239 • Subnet Mask: 255.255.255.0 Later, you may want to change the network parameters to match those of your network (this procedure is described in Chapter 3, "Managing System Settings" in "Setup" on page 3-6). Your host PC network parameters must then also be set back to match your network. Clicking Web Access on the SmartWizard Discovery utility or accessing the switch directly displays the page shown below. . Figure 1-5 Use this page to proceed to management of the switch covered in Chapter 2, "Introduction to the Web Browser Interface". Additional Utilities Alternatively, from the main page shown on Figure 1-1 on page 1-3 you can access these additional functions: • "Password Change" Getting Started with Switch Management 1-7 v1.0, May 2007

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
GS108T Smart Switch Software Administration Manual
Getting Started with Switch Management
1-7
v1.0, May 2007
If you are starting with an “out of the box” switch and are not using the SmartWizard Discovery
utility, you must initially configure your host PC to be on a network segment to match the default
parameters of the switch, which are:
•
IP address: 192.168.0.239
•
Subnet Mask: 255.255.255.0
Later, you may want to change the network parameters to match those of your network (this
procedure is described in
Chapter 3, “Managing System Settings”
in
“Setup” on page 3-6
). Your
host PC network parameters must then also be set back to match your network.
Clicking
Web Access
on the SmartWizard Discovery utility or accessing the switch directly
displays the page shown below.
.
Use this page to proceed to management of the switch covered in
Chapter 2, “Introduction to the
Web Browser Interface”
.
Additional Utilities
Alternatively, from the main page shown on
Figure 1-1 on page 1-3
you can access these
additional functions:
•
“Password Change”
Figure 1-5