Home » Netgear Manuals » Hubs & Switches » Netgear GS108T » Manual Viewer

Netgear GS108T GS108T Setup Manual - Page 99

File Download, Configuration Download - downloads

UPC - 606449051377

Add to My Manuals
Save this manual to your list of manuals

Page 99 highlights

GS108T Smart Switch Software Administration Manual File Download File Download enables you to download the firmware and configuration from the TFTP Server or HTTP Host to restore or update the switch. . Note: You can also update the firmware using the in the SmartWizard Discovery utility (see "Firmware Upgrade" on page 1-8). 1. Click File Download in the blue navigation panel. A screen similar to that shown below appears. . Figure 5-60 2. Click Firmware Download or Configuration Download to select the type of file for download. 3. Click TFTP or HTTP to select the download mode. If the TFTP mode is selected: a. Enter the IP Address of the TFTP Server. b. Enter the name of the firmware or configuration source file in the TFTP server. Managing Firmware and Reset Options 5-3 v1.0, May 2007

Section	Page
GS108T Smart Switch Software Administration Manual	1
Contents	5
About This Manual	7
Who Should Use this Book	7
How to Use This Book	7
Conventions, Formats, and Scope	8
How to Use This Manual	9
How to Print this Manual	9
Revision History	10
Chapter 1 Getting Started with Switch Management	11
System Requirements	11
Switch Management Interface	12
Network with a DHCP Server	13
Network without a DHCP Server	14
Manually Assigning Network Parameters	15
NIC Setting on the Host that Accesses the GS108T Gigabit Smart Switch	15
Web Access	16
Additional Utilities	17
Password Change	18
Firmware Upgrade	18
Exit	20
Chapter 2 Introduction to the Web Browser Interface	21
Logging Into the NETGEAR Home Page	21
The Navigation Menu	22
Other Features of the Browser Interface	23
Chapter 3 Managing System Settings	25
Using the System Settings Utility	25
Switch Status	25
IP Access List	27
Setup	30
Management Security	32
Password	32
RADIUS Server	33
MAC Address Table	35
Static Address	35
Dynamic Address	36
Time	38
LLDP	39
LLDP Configuration	39
LLDP Statistics	42
Local Information	43
MSAP (Remote) Information	46
Logs	49
Logs Configuration	49
Memory Logs	50
Flash Logs	51
Server Logs	52
Chapter 4 Configuring the Switch	55
Using the Switch Configuration Utility	55
Port Configuration	55
Statistics	58
QoS	61
VLAN	63
VLAN Group Setting	63
Management VLAN Setting	70
Link Aggregation	71
LAG Setting	72
LACP	73
Monitor	74
Advanced	76
Jumbo Frame	76
Rate Limiting	76
Storm Control	78
Spanning Tree	79
SNMP	81
Multicast	83
IGMP Snooping	83
Unknown Multicast	84
Static Multicast Group	85
Security	85
Properties	86
Port Authentication	87
EAP Statistics	90
Statistics	92
Port Security	93
Trusted MAC	94
Chapter 5 Managing Firmware and Reset Options	97
File Management	97
File Upload	97
File Download	99
Factory Reset	100
Reset	101
Appendix A Specifications and Default Values	103
GS108T Gigabit Smart Switch Specifications	103
GS108T Gigabit Smart Switch Features and Defaults	104
Appendix B Virtual Local Area Networks (VLANs)	107
IEEE 802.1Q VLANs	108
Port-based VLANs	109
Port-based VLAN Example Configuration	109
Results of this Configuration	110
Appendix C Network Cabling	111
Fast Ethernet Cable Guidelines	111
Category 5 Cable	111
Category 5 Cable Specifications	112
Twisted Pair Cables	112
Cabling	114
Near End Cross Talk (NEXT)	115
Patch Cables	116
RJ-45 Plug and RJ-45 Connectors	116
Conclusion	117