Netgear WG302 WG302v1 Reference Manual - Page 49

Management, Using the Secure Telnet Interface, How to Use the CLI via the Console Port

Get Netgear WG302 - 802.11g ProSafe Wireless Access Point PDF manuals and user guides
UPC - 606449030365
View all Netgear WG302 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

Chapter 4 Management This chapter describes how to use the management features of your NETGEAR ProSafe Wireless Access Point 802.11g WG302 . These features can be found by clicking on the Maintenance heading in the Main Menu of the browser interface. Using the Secure Telnet Interface The WG302 includes a secure Telnet command line interface (CLI). You can access the CLI from a secure Telnet client over the Ethernet port or over the serial console port. . Note: You must use a secure Telnet client such as Absolute Telnet. Also, when you configure the client, use the SSH1, 3DES option. If you use the Telnet client to connect over the Ethernet port, use the IP address of the WG302 as the host name. How to Use the CLI via the Console Port 1. Using the null-modem cable, connect a VT100/ANSI terminal or a workstation to the port labeled Console. If you attached a PC, Apple Macintosh, or UNIX workstation, start a secure terminal-emulation program. 2. Configure the terminal-emulation program to use the following settings: • Baud rate: 9,600 bps • Data bits: 8 • Parity: none • Stop bit: 1 • Flow control: none These settings appear below the connector on the back panel. Management 4-1 September 2004

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Management
4-1
September 2004
Chapter 4
Management
This chapter describes how to use the management features of your NETGEAR ProSafe Wireless
Access Point 802.11g WG302 . These features can be found by clicking on the Maintenance
heading in the Main Menu of the browser interface.
Using the Secure Telnet Interface
The WG302 includes a secure Telnet command line interface (CLI). You can access the CLI from
a secure Telnet client over the Ethernet port or over the serial console port.
.
How to Use the CLI via the Console Port
1.
Using the null-modem cable, connect a VT100/ANSI terminal or a workstation to the
port labeled Console.
If you attached a PC, Apple Macintosh, or UNIX workstation, start a secure
terminal-emulation program.
2.
Configure the terminal-emulation program to use the following settings:
•
Baud rate: 9,600 bps
•
Data bits: 8
•
Parity: none
•
Stop bit: 1
•
Flow control: none
These settings appear below the connector on the back panel.
Note:
You must use a secure Telnet client such as Absolute Telnet. Also, when you
configure the client, use the SSH1, 3DES option. If you use the Telnet client to connect
over the Ethernet port, use the IP address of the WG302 as the host name.