Netgear WG302 WG302v1 Reference Manual - Page 67

How to Con a WG302 as a Point-to-Point Bridge, Segment 1 - network address

Get Netgear WG302 - 802.11g ProSafe Wireless Access Point PDF manuals and user guides
UPC - 606449030365
View all Netgear WG302 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Reference Manual for the NETGEAR ProSafe Wireless Access Point 802.11g WG302 How to Configure a WG302 as a Point-to-Point Bridge AP1 AP in R ESET ETHER N ET 5 -1 2 V DC Point-to-Point Bridge Mode Router AP2 AP in R ESET ETHER N ET 5 -1 2 V DC Point-to-Point Bridge Mode Hub or Switch LAN Segment 1 LAN Segment 2 Figure 5-6: Point-to-Point Bridge 1. Configure the WG302 (AP1) on LAN Segment 1 in Point-to-Point Bridge mode. 2. Configure the WG302 (AP2) on LAN Segment 2 in Point-to-Point Bridge mode. AP1 must have AP2's MAC address in its Remote MAC Address field and AP2 must have AP1's MAC address in its Remote MAC Address field. 3. Configure and verify the following parameters for both access points: • Verify that the LAN network configuration of the WG302 Access Points both are configured to operate in the same LAN network address range as the LAN devices • Both use the same ESSID, Channel, authentication mode, if any, and security settings if security is in use. 4. Verify connectivity across the LAN 1 and LAN 2. • A computer on either LAN segment should be able to connect to the Internet or share files and printers of any other PCs or servers connected to LAN Segment 1 or LAN Segment 2. Advanced Configuration 5-7 September 2004

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Reference Manual for the NETGEAR ProSafe Wireless Access Point 802.11g WG302
Advanced Configuration
5-7
September 2004
How to Configure a WG302 as a Point-to-Point Bridge
Figure 5-6:
Point-to-Point Bridge
1.
Configure the WG302 (AP1) on LAN Segment 1 in Point-to-Point Bridge mode.
2.
Configure the WG302 (AP2) on LAN Segment 2 in Point-to-Point Bridge mode.
AP1 must have AP2’s MAC address in its Remote MAC Address field and AP2 must have
AP1’s MAC address in its Remote MAC Address field.
3.
Configure and verify the following parameters for both access points:
•
Verify that the LAN network configuration of the WG302 Access Points both are
configured to operate in the same LAN network address range as the LAN devices
•
Both use the same ESSID, Channel, authentication mode, if any, and security settings if
security is in use.
4.
Verify connectivity across the LAN 1 and LAN 2.
•
A computer on either LAN segment should be able to connect to the Internet or share files
and printers of any other PCs or servers connected to LAN Segment 1 or LAN Segment 2.
LAN
Segment 1
Router
AP in
Point-to-Point
Bridge Mode
AP in
Point-to-Point
Bridge Mode
LAN
Segment 2
Hub or Switch
AP1
AP2