Netgear WG602 WG602v3 User Manual - Page 29

Understanding the Basic Wireless Settings, The IP Address Source, Spanning Tree Protocol, Apply - wg602v3 default ip address

Get Netgear WG602 - 54 Mbps Wireless Access Point PDF manuals and user guides
UPC - 606449030730
View all Netgear WG602 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Reference Manual for the NETGEAR 54 Mbps Wireless Access Point WG602v3 • The IP Address Source The wireless access point is shipped preconfigured to use a private IP address on the LAN side, and to act as a DHCP client. If the wireless access point does not find a DHCP server on the Ethernet LAN, it defaults to this IP configuration: - DHCP Client - Enable - IP Address - 192.168.0.227 - IP Subnet Mask - 255.255.255.0 - Gateway - 0.0.0.0 If your network has a requirement to use a different IP addressing scheme, you can make those changes in this page. • Spanning Tree Protocol Spanning Tree Protocol in enabled by default for the wireless access point. This provides network traffic optimization in settings with multiple WG602v3 Access Points. Remember to click Apply to save your changes. Understanding the Basic Wireless Settings To configure the wireless settings of your wireless access point, click the Wireless Settings link in the Setup section of the main menu of the browser interface. The Wireless Settings page appears, as shown below. Figure 3-9: Basic Wireless Settings page Basic Installation and Configuration 202-10060-02, February 2005 3-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
Reference Manual for the NETGEAR 54 Mbps Wireless Access Point WG602v3
Basic Installation and Configuration
3-11
202-10060-02, February 2005
•
The IP Address Source
The wireless access point is shipped preconfigured to use a private IP address on the LAN
side, and to act as a DHCP client. If the wireless access point does not find a DHCP server on
the Ethernet LAN, it defaults to this IP configuration:
–
DHCP Client -
Enable
–
IP Address — 192.168.0.227
–
IP Subnet Mask — 255.255.255.0
–
Gateway — 0.0.0.0
If your network has a requirement to use a different IP addressing scheme, you can make those
changes in this page.
•
Spanning Tree Protocol
Spanning Tree Protocol in enabled by default for the wireless access point. This provides
network traffic optimization in settings with multiple WG602v3 Access Points.
Remember to click
Apply
to save your changes.
Understanding the Basic Wireless Settings
To configure the wireless settings of your wireless access point, click the Wireless Settings link in
the Setup section of the main menu of the browser interface. The Wireless Settings page appears,
as shown below.
Figure 3-9:
Basic Wireless Settings page