NordicTrack C 1270 Pro Treadmill English Manual - Page 12

not overtighten the #10 x 3/4 Screws 9.

Get NordicTrack C 1270 Pro Treadmill PDF manuals and user guides View all NordicTrack C 1270 Pro Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

6. Attach a Handrail (86) to the Right Upright (90) with two 5/16" x 2 1/2" Screws (28) and two 5/16" Star Washers (11); do not fully tighten the Screws yet. Make sure not to pinch the Upright Wire (81), and make sure that the wire is on the indicated side of the Upright. Attach the other Handrail (86) to the Left Upright (89) in the same way. Note: There are no wires on the left side. Then, remove and discard the indicated screws (E). 6 11 E 28 86 28 89 11 E 86 90 81 7. IMPORTANT: To avoid damaging the Pulse Crossbar (93), do not use power tools and do not overtighten the #10 x 3/4" Screws (9). Orient the Pulse Crossbar (93) as shown. Attach the Pulse Crossbar to the Handrails (86) with four #10 x 3/4" Screws (9) and four #10 Star Washers (5); start all four Screws, and then tighten them. Next, firmly tighten the four 5/16" x 2 1/2" Screws (28). Then, remove the wire tie (A) from the Upright Wire (81). 7 9 5 28 86 93 9 5 86 81 28 A 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
12
6
81
90
89
86
E
86
28
11
11
28
6.
Attach a Handrail (86) to the Right Upright (90)
with two 5/16" x 2 1/2" Screws (28) and two
5/16" Star Washers (11);
do not fully tighten
the Screws yet. Make sure not to pinch the
Upright Wire (81), and make sure that the
wire is on the indicated side of the Upright.
Attach the other Handrail (86) to the Left
Upright (89) in the same way.
Note: There are
no wires on the left side.
Then, remove and discard the indicated screws
(E).
E
9
9
28
28
5
5
81
93
A
7
7.
IMPORTANT: To avoid damaging the Pulse
Crossbar (93), do not use power tools and do
not overtighten the #10 x 3/4" Screws (9).
Orient the Pulse Crossbar (93) as shown. Attach
the Pulse Crossbar to the Handrails (86) with
four #10 x 3/4" Screws (9) and four #10 Star
Washers (5);
start all four Screws, and then
tighten them.
Next, firmly tighten the four 5/16" x 2 1/2"
Screws (28).
Then, remove the wire tie (A) from the Upright
Wire (81).
86
86