NordicTrack Se 3i Instruction Manual - Page 12

Tip: Avoid pinching the Pulse Wires 23.

Get NordicTrack Se 3i PDF manuals and user guides View all NordicTrack Se 3i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

14. Have a second person hold the Handlebar (22) in place around the Upright (2). Next, locate the Pulse Wires (23) inside the left and right sides of the Handlebar (22), and carefully pull them through the Upright (2) as shown. Tip: Avoid pinching the Pulse Wires (23). Attach the Handlebar (22) to the Upright (2) with three M10 x 20mm Screws (79); start all the Screws, and then tighten them. 14 23 Avoid pinching the Pulse Wires (23) 79 79 22 2 15. Untie and discard the wire tie attached to the Main Wire (89). 15 5 While a second person holds the Console (5) near the Upright (2), plug the Main Wire (89) and the Pulse Wires (23) into the receptacles on the Console. The connectors on the Main Wire (89) and the Pulse Wires (23) should slide easily into the receptacles and snap into place. If a connector does not slide easily into a receptacle, turn the connector and try again. If you do not connect the connectors properly, the Console (5) may become damaged when you use the elliptical. Insert the excess wire into the Upright (2). Tip: Avoid pinching the wires. Attach the Console (5) to the Upright (2) with four M4 x 12mm Screws (77); start all the Screws, and then tighten them. Avoid pinching the wires 89 2 77 23 77 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
12
79
79
22
14
14.
Have a second person hold the Handlebar (22)
in place around the Upright (2).
Next, locate the Pulse Wires (23) inside the left
and right sides of the Handlebar (22), and care-
fully pull them through the Upright (2) as shown.
Tip: Avoid pinching the Pulse Wires (23).
Attach the Handlebar (22) to the Upright (2) with
three M10 x 20mm Screws (79);
start all the
Screws, and then tighten them.
Avoid
pinching
the Pulse
Wires (23)
23
77
77
5
2
89
15
15. Untie and discard the wire tie attached to the
Main Wire (89).
While a second person holds the Console (5)
near the Upright (2), plug the Main Wire (89) and
the Pulse Wires (23) into the receptacles on the
Console.
The connectors on the Main Wire (89) and the
Pulse Wires (23) should slide easily into the
receptacles and snap into place.
If a connector
does not slide easily into a receptacle, turn the
connector and try again.
If you do not connect
the connectors properly, the Console (5) may
become damaged when you use the elliptical.
Insert the excess wire into the Upright (2).
Tip: Avoid pinching the wires.
Attach
the Console (5) to the Upright (2) with four
M4 x 12mm Screws (77);
start all the Screws,
and then tighten them.
Avoid pinching
the wires
23
2