Olympus E-500 EVOLT E-500 Advanced Manual (English) - Page 173

The computer does not recognize the camera correctly., The monitor is hard to see. - record video

Get Olympus E-500 - EVOLT Digital Camera PDF manuals and user guides
UPC - 050332299405
View all Olympus E-500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 173 highlights

If you encounter problems Possible cause Corrective action Ref. Page The top left part of the picture appears too bright. When shooting at slow shutter speeds, noise may be generated due to a rise in temperature in the CCD drive circuit. Set [NOISE REDUCTION] to [ON] before taking pictures. P. 95 Pictures cannot be played back on the monitor. Pictures are not stored on "NO PICTURE" appears on the monitor. Record - the card. pictures. The card error occurs. Refer to the error messages. P. 168 No picture is displayed on the TV when connected to the camera. The video cable is not connected correctly. Connect the cable properly according to the instructions. P. 108 The camera's video output Set the video signal according to the region signal is incorrect. where used. P. 135 The TV 's video signal is Set the TV to the video input mode. - incorrect. The monitor is hard to see. The brightness is not adjusted properly. Adjust the brightness of the monitor using the menu. P. 133 The monitor is exposed to Block the sunlight with your hand. - direct sunlight. The computer does not recognize the camera correctly. The camera's power is Set the power switch to ON. - turned off. The USB driver was not successfully installed. Install the OLYMPUS Master. P. 155 The camera is in the [CONTROL] mode. Set [USB MODE] to [AUTO] or [STORAGE]. When [AUTO] is set, the selection screen for USB connection is displayed every time you connect the USB cable to the camera. P. 134 11 Appendix 173

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
173
If you encounter problems
11
Appendix
The top left part of the picture appears too bright.
When shooting at slow
shutter speeds, noise may
be generated due to a rise
in temperature in the CCD
drive circuit.
Set [NOISE REDUCTION] to [ON] before taking
pictures.
P. 95
Pictures cannot be played back on the monitor.
Pictures are not stored on
the card.
“NO PICTURE” appears on the monitor. Record
pictures.
–
The card error occurs.
Refer to the error messages.
P. 168
No picture is displayed on the TV when connected to the camera.
The video cable is not
connected correctly.
Connect the cable properly according to the
instructions.
P. 108
The camera's video output
signal is incorrect.
Set the video signal according to the region
where used.
P. 135
The TV 's video signal is
incorrect.
Set the TV to the video input mode.
–
The monitor is hard to see.
The brightness is not
adjusted properly.
Adjust the brightness of the monitor using the
menu.
P. 133
The monitor is exposed to
direct sunlight.
Block the sunlight with your hand.
–
The computer does not recognize the camera correctly.
The camera's power is
turned off.
Set the power switch to ON.
–
The USB driver was not
successfully installed.
Install the OLYMPUS Master.
P. 155
The camera is in the
[CONTROL] mode.
Set [USB MODE] to [AUTO] or [STORAGE].
When [AUTO] is set, the selection screen for
USB connection is displayed every time you
connect the USB cable to the camera.
P. 134
Possible cause
Corrective action
Ref. Page