Onkyo TX-SR393 AV Receiver Owners Manual - English - Page 67

Speaker, Configuration

Get Onkyo TX-SR393 AV Receiver PDF manuals and user guides View all Onkyo TX-SR393 AV Receiver manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Contents ≫ Connections ≫ Playback ≫ Setup ≫ 2. Speaker „„1. Configuration Change the settings of connection environment of the speakers. Setting Item Speaker Channels Subwoofer Height Speaker Speaker Impedance Default Value Setting Details 5.1 ch Select "2.1 ch", "3.1 ch", "4.1 ch", "5.1 ch", "2.1.2 ch" or "3.1.2 ch" to suit the number of speaker channels connected. Yes Set whether a subwoofer is connected or not. "Yes": When a subwoofer is connected "No": When a subwoofer is not connected Top Middle Set the speaker type if height speakers are connected to the SURROUND or HEIGHT terminals. Select "Top Middle", "Dolby Speaker (Front)" or "Front High" according to the type and layout of the connected speakers. • If the item cannot be selected even though connection is correct, check if the setting in "Speaker Channels" matches the number of connected channels. 6 ohms or above Set the impedance (Ω) of the connected speakers. "4 ohms": When any of the connected speakers have 4 Ω or more to less than 6 Ω impedance "6 ohms or above": When the connected speakers all have 6 Ω or more impedance • For impedance, check the indications on the back of the speakers or their instruction manual. „„2. Crossover Change the settings of crossover frequencies. Setting Item Front Center Height Default Value 100 Hz 100 Hz 100 Hz Setting Details Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting frequencies for each channel. "Full Band": Full band will be output. • If "Configuration" - "Subwoofer" is set to "No", "Front" is fixed to "Full Band", and the low pitched range of the other channels is output from the front speakers. Refer to the instruction manual of your speakers to make the setting. Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting frequencies for each channel. "Full Band": Full band will be output. • "Full Band" can be selected only when "Front" is set to "Full Band". • If the item cannot be selected even though connection is correct, check if the setting in "Configuration" - "Speaker Channels" matches the number of connected channels. Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting frequencies for each channel. "Full Band": Full band will be output. • "Full Band" can be selected only when "Front" is set to "Full Band". • If the item cannot be selected even though connection is correct, check if the setting in "Configuration" - "Speaker Channels" matches the number of connected channels. 67 Front Panel≫ Rear Panel≫ Remote≫

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
67
Front Panel
≫
Rear Panel
≫
Remote
≫
Contents
≫
Connections
≫
Playback
≫
Setup
≫
2. Speaker
±
1. Configuration
Change the settings of connection environment of the speakers.
Setting Item
Default Value
Setting Details
Speaker
Channels
5.1 ch
Select "2.1 ch", "3.1 ch", "4.1 ch", "5.1 ch",
"2.1.2 ch" or "3.1.2 ch" to suit the number of
speaker channels connected.
Subwoofer
Yes
Set whether a subwoofer is connected or not.
"Yes": When a subwoofer is connected
"No": When a subwoofer is not connected
Height Speaker
Top Middle
Set the speaker type if height speakers are
connected to the SURROUND or HEIGHT
terminals.
Select "Top Middle", "Dolby Speaker (Front)" or
"Front High" according to the type and layout of the
connected speakers.
•
If the item cannot be selected even though
connection is correct, check if the setting in
"Speaker Channels" matches the number of
connected channels.
Speaker
Impedance
6 ohms or above
Set the impedance (Ω) of the connected speakers.
"4 ohms": When any of the connected speakers
have 4 Ω or more to less than 6 Ω impedance
"6 ohms or above": When the connected speakers
all have 6 Ω or more impedance
•
For impedance, check the indications on the
back of the speakers or their instruction manual.
±
2. Crossover
Change the settings of crossover frequencies.
Setting Item
Default Value
Setting Details
Front
100 Hz
Select the crossover frequency from "40 Hz" to
"200 Hz" to start outputting frequencies for each
channel.
"Full Band": Full band will be output.
•
If "Configuration" - "Subwoofer" is set to "No",
"Front" is fixed to "Full Band", and the low
pitched range of the other channels is output
from the front speakers. Refer to the instruction
manual of your speakers to make the setting.
Center
100 Hz
Select the crossover frequency from "40 Hz" to
"200 Hz" to start outputting frequencies for each
channel.
"Full Band": Full band will be output.
•
"Full Band" can be selected only when "Front" is
set to "Full Band".
•
If the item cannot be selected even though
connection is correct, check if the setting in
"Configuration" - "Speaker Channels" matches
the number of connected channels.
Height
100 Hz
Select the crossover frequency from "40 Hz" to
"200 Hz" to start outputting frequencies for each
channel.
"Full Band": Full band will be output.
•
"Full Band" can be selected only when "Front" is
set to "Full Band".
•
If the item cannot be selected even though
connection is correct, check if the setting in
"Configuration" - "Speaker Channels" matches
the number of connected channels.