Panasonic 26PEU1U6 Installation Instructions - Page 49

Misoperation Alarm Indicators, Table 5-2, Fig. 5-24, Fig. 5-25

Get Panasonic 26PEU1U6 PDF manuals and user guides View all Panasonic 26PEU1U6 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

5-15. Misoperation Alarm Indicators A blinking lamp for other than the signal receiving unit filter shows that a problem has occurred in the unit, so make an inspection. (Refer to servicing information in the service manual, etc.) Also, if wired remote controller and dedicated service check lines (CV6380230938: service use) are available, then detailed error information can be obtained by connecting to the service connector as shown in the drawing. For information on how to connect to the signal receiving unit, refer to the instruction manual that came with the dedicated service check lines. Service connector ALL• RCU : SUB PCB CHK. TEST RUN RCU : MAIN NORMAL Fig. 5-24 8. Transmitter 9. Remote control sensor 1. Operation Display 2. Start/Stop button 3. Fan speed button 4. Swing/Wind Direction button 5. Timer setting button 6. Reset button 7. Cover 10. Temperature setting buttons 11. Filter button 12. Mode Select button 13. Ventilation button 14. Address button 15. Sensor button 16. Clock button Fig. 5-25 Table 5-2 OPERATION lamp Lamp TIMER lamp STANDBY lamp Bright Alternately Alternately Concurrent Concurrent Cause of Trouble No power supply or mis-wiring of signal receiving unit. S.C.* errors between the indoor unit's controller (PCB) and signal receiving unit. S.C. errors between indoor and outdoor units. Indoor unit protector is activated. Outdoor unit protector is activated. Compressor protector is activated. Mis-setting of indoor unit. Mis-setting of outdoor unit. * S.C.: Serial communications 49 1BOBTPOJD@1"$J@*OEPPS6OJU@64MF

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
49
5-15. Misoperation Alarm Indicators
A blinking lamp for other than the signal receiving unit
filter shows that a problem has occurred in the unit, so
make an inspection. (Refer to servicing information in
the service manual, etc.) Also, if wired remote controller
and dedicated service check lines (CV6380230938:
service use) are available, then detailed error
information can be obtained by connecting to the
service connector as shown in the drawing. For
information on how to connect to the signal receiving
unit, refer to the instruction manual that came with the
dedicated service check lines.
Table 5-2
Fig. 5-24
Fig. 5-25
Lamp
OPERATION
TIMER
STANDBY
Brig
u
a
C
t
h
se of Trouble
lamp
lamp
lamp
No power supply or mis-wiring of signal receiving unit.
S.C.* errors between the indoor unit’s controller (PCB) and
signal receiving unit.
S.C. errors between indoor and outdoor units.
Alternately
Indoor unit protector is activated.
Alternately
Outdoor unit protector is activated.
Compressor protector is activated.
Concurrent
Mis-setting of indoor unit.
Concurrent
Mis-setting of outdoor unit.
*
S.C.: Serial communications
ALL•
RCU : SUB
RCU : MAIN
NORMAL
PCB CHK.
TEST RUN
Service
connector
1. Operation Display
2. Start/Stop button
3. Fan speed button
4. Swing/Wind Direction button
5. Timer setting button
6. Reset button
7. Cover
8. Transmitter
9. Remote control sensor
10. Temperature setting buttons
12. Mode Select button
11. Filter button
13. Ventilation button
14. Address button
15. Sensor button
16. Clock button
Panasonic_PAC-i_IndoorUnit_US-le49 49
Panasonic_PAC-i_IndoorUnit_US-le49
49
2011/11/02 15:17:37
2011/11/02
15:17:37