Panasonic 3-MOS P2 Hand-held Camcorder Advanced Operating Instructions - Page 71

Shooting Recording time codes and user bits When SYSTEM MODE is set to 1080-59.94i, 720-59.94P, 480-59.94i System setting status Recorded TC Output TC Displayed TC Recorded UB Output UB SYSTEM REC MODE SIGNAL REC FORMAT CAMERA FRAME MODE RATE LTC LTC and VITC TC OUT VITC TC tc (24/30 embedded conversion) LTC UB in HD SDI TC IN/OUT LTC UB VITC UB VITC UB connector embedded embedded UB*1 in HD SDI*1 in HD SDI DVCPROHD/60i 60i, 30P (60i) - 1 to 30 FRAME 24P, 24PA - R-RUN/F-RUN*3 DF/NDF 30 frames R-RUN/F-RUN*5 NDF locked 30 frames Outputs Outputs LTC LTC AVC-I100/60i AVC-I50/60i - AVC-I100/30PN CAMERA AVC-I50/30PN - 108059.94i - 1 to 30 FRAME R-RUN/F-RUN*3 DF/NDF 30 frames - R-RUN/F-RUN*3 DF/NDF 30 FRAME 30 frames Outputs LTC Outputs LTC Outputs LTC Outputs LTC TC: 30 frames tc: 24 frames R-RUN locked Other than 30 FRAME DF/NDF Every active frame 30 frames Same as LTC value Matches recorder TC at start of Matches recorder TC at start of recording recording 30 frames/ 30 frames/ s s Outputs Outputs LTC UB LTC UB Follows UB MODE. ·In 'EXT' Frame rate slaves to UB data in TC IN/OUT connector Frame rate data AVC-I100/24PN AVC-I50/24PN - - R-RUN/F-RUN*7 NDF locked 24 FRAME 24 frames R-RUN locked Other than 24 FRAME NDF locked Every active frame 24 frames Converts Converts and outputs and outputs LTC to 30 LTC to 30 Recording frames frames TC: 24 frames Matches Matches Playback recorder recorder TC: TC at TC at 24 frames start of start of tc: recording recording 30 frames 30 frames/ 30 frames/ s s Output Output adjusted adjusted to Over to Over 60i based 60i based on LTC on LTC UB UB 1394 DVCPROHD/60i - - Records R-RUN/F-RUN*2 DF/NDF 30 frames VAUX TC in 1394 input at Outputs LTC all times*6 Outputs LTC TC: 30 frames tc: 24 frames Follows UB MODE. ·In 'EXT' slaves to LTC UB in 1394 input Records VITC UB in Outputs 1394 input at LTC UB all times Outputs LTC UB Outputs VITC UB *1: When UB MODE is FRM. RATE, playback of native clips is the pulldown frame rate read from VITC UB. *2: In Free Run mode, it is slaved to the value input to the DVCPRO/DV connector. It does not slave it to the time code from the TC IN/OUT connector. *3: In Free Run mode, it is slaved to the time code input to the TC IN/OUT connector. *5: In Free Run mode, it is slaved when TC input to the TC IN/OUT connector is non-drop frame. But not slaved to it during recording. *6: VAUX TC is time code recorded in the video AUX area in the DVC format. *7: In Free Run mode, it is slaved to the time code input to the TC IN/OUT connector, whose value is converted to 24 frames when it was NDF 30 frames. But not slaved to it during recording. 71