Panasonic AW-HS50 Operating Instructions - Page 40

System settings, System menu settings

Page 40 highlights

4. System settings 4-1. System menu settings 4-1-1. Setting the video format The unit's video format can be set. =?5;56'//GPW (QTOCV *K4GU/8 53 #7:#PEK 2)/#PEK 289#PEK /8#PEK +PKVKCN +2#FFTGUU 5WDPGV/CUM )CVGYC[ K   1HH 1HH 1HH 1HH 0Q Note The [14] SYSTEM Menu settings cannot be changed if "Locked" has been set using the menu item below. [13] Operation Menu 11. SYSTEM Menu [14] SYSTEM Menu 1. Format Select the supported format from among the options provided below. Supported formats 1080/59.94i 1080/50i 720/59.94p 720/50p 1080/24PsF 1080/23.98PsF 480/59.94i 576/50i With the unit in the power-off status, the video format can be specified and the system started. Set the POWER switch to ON while holding down one combination of the buttons listed below that corresponds to the video format. Button to press at the same time Video format [OSD ON] + A bus crosspoint [1] 1080/59.94i [OSD ON] + A bus crosspoint [2] 1080/50i [OSD ON] + A bus crosspoint [3] 720/59.94p [OSD ON] + A bus crosspoint [4] 720/50p [OSD ON] + A bus crosspoint [5] 1080/24PsF [OSD ON] + B bus crosspoint [1] 1080/23.98PsF [OSD ON] + B bus crosspoint [2] 480/59.94i [OSD ON] + B bus crosspoint [3] 576/50i  After the POWER switch has been set to ON, keep holding down the buttons until an image is output. [14] SYSTEM Menu 2. HiResMV This is used to decide whether to set the high-resolution multi view mode. When an SD video format (480/59.94i or 576/50i) has been selected for the unit, the images can be output at high resolution to the DVI-D output. If this is the case, the multi view display is set for the DVI OUT connector output. The multi view display cannot be set for the SDI OUT connector output. On: The high-resolution multi view mode is enabled. Off: The high-resolution multi view mode is disabled. [14] SYSTEM Menu 3. 16:9SQ This is used to set the 16:9 squeeze mode. It can be set when an SD video format (480/59.94i or 576/50i) has been selected for the unit. When adjusting the wipe and PinP border width, bear in mind that the SD format images that are output from the unit will be converted into the 16:9 aspect ratio and used. Unit's output (4:3 aspect ratio) Images converted into 16:9 aspect ratio 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68

40
4.
System settings
4-1.
System menu settings
4-1-1.
Setting the video format
The unit’s video format can be set.
°
±²(QTOCV
±¾¼¾¿¹½²½¸K
¶²*K4GU/8
³
·²±ºÀ½53
³
¸²#7: #PEK
1HH
¹²2)/ #PEK
1HH
º²289 #PEK
1HH
»²/8 #PEK
1HH
¼²+PKVKCN
0Q
½²+2 #FFTGUU
±½¶²
±º¼²
¾²
¼
±¾²5WDPGV /CUM
¶¹¹²
¶¹¹²
¶¹¹²
¾
±±²)CVGYC[
±½¶²
±º¼²
¾²
±
=±¸? 5;56'/ /GPW
The [14] SYSTEM Menu settings cannot be changed if
“Locked” has been set using the menu item below.
[13] Operation Menu
11. SYSTEM Menu
Note
[14] SYSTEM Menu
1. Format
Select the supported format from among the options
provided below.
Supported formats
1080/59.94i
1080/50i
720/59.94p
720/50p
1080/24PsF
1080/23.98PsF
480/59.94i
576/50i
<How to specify the video format and then start
the system>
With the unit in the power-off status, the video format can be
specified and the system started.
Set the POWER switch to ON while holding down one
combination of the buttons listed below that corresponds to
the video format.
Button to press at the same time
Video format
[OSD ON] + A bus crosspoint [1]
1080/59.94i
[OSD ON] + A bus crosspoint [2]
1080/50i
[OSD ON] + A bus crosspoint [3]
720/59.94p
[OSD ON] + A bus crosspoint [4]
720/50p
[OSD ON] + A bus crosspoint [5]
1080/24PsF
[OSD ON] + B bus crosspoint [1]
1080/23.98PsF
[OSD ON] + B bus crosspoint [2]
480/59.94i
[OSD ON] + B bus crosspoint [3]
576/50i
After the POWER switch has been set to ON, keep
holding down the buttons until an image is output.
[14] SYSTEM Menu
2. HiResMV
This is used to decide whether to set the high-resolution
multi view mode.
When an SD video format (480/59.94i or 576/50i) has been
selected for the unit, the images can be output at high
resolution to the DVI-D output.
If this is the case, the multi view display is set for the DVI
OUT connector output.
The multi view display cannot be set for the SDI OUT
connector output.
On:
The high-resolution multi view mode is enabled.
Off:
The high-resolution multi view mode is disabled.
[14] SYSTEM Menu
3. 16:9SQ
This is used to set the 16:9 squeeze mode.
It can be set when an SD video format (480/59.94i or
576/50i) has been selected for the unit.
When adjusting the wipe and PinP border width, bear in
mind that the SD format images that are output from the unit
will be converted into the 16:9 aspect ratio and used.
<Border width when the 16:9SQ mode has been
enabled (graphical representation)>
Unit’s output
(4:3 aspect ratio)
Images converted into
16:9 aspect ratio