Panasonic WJ-PR204 Operating Instructions - Page 18

Precautions before receiver installations, Preface, For WJ-PR204E/WJ-PR201E: BY-HCA10CE

Get Panasonic WJ-PR204 PDF manuals and user guides View all Panasonic WJ-PR204 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

1 Preface 4. Precautions before receiver installations PR204 PR201 • When mounting 3 to 4 connected receiver side units to the rack, use the following bracket (locally procured). - Rack mount bracket: For WJ-PR204/WJ-PR201: BY-HCA10A For WJ-PR204E/WJ-PR201E: BY-HCA10CE • Available racks - EIA standard rack or equivalent (third party) EIA19 type • Rack mounting screws - M5 ´ 12 mm {15/32 inches} screws 5. Precautions before camera installations PC200 • Use the screws with the specifications shown on page 25 when mounting the camera side unit to a ceiling or wall. Screws are included with camera side unit. Use screws that are appropriate for the material of the ceiling or wall. • When mounting the camera side unit to a ceiling or wall (see page 25), do not drive the screws into a soft material. Drive the screws into a secure, 25 mm (1 inch) thick area of the ceiling or wall, such as a crossbeam, otherwise the camera side unit may fall. If there is no crossbeam, place a board on the other side of the ceiling or wall to make sure the camera side unit is securely mounted. • When mounting a camera side unit on a concrete or mortar ceiling or wall, use a drill and anchors (locally procured, body diameter 4 mm {3/16 inches}) and make holes using the following procedure. i. Mark points where you are going to make holes (2 places) according to the position of the camera side unit. ii. Make holes in the areas that you marked with an electric drill. • Mortar ceilings break easily when drilling. Be careful of pieces of mortar which may become loose and fall. iii. Insert the anchors (locally procured) into the holes and push them inside with a hammer. Drill for concrete (in case of tile, use a drill for tile) Caulk to waterproof • Mount the camera side unit to a secure area and make sure that the anchors and screws are secured. 18 Operating Instructions

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
4.
Precautions before receiver installations
PR204
PR201
•
When mounting 3 to 4 connected receiver side units to the rack, use the following
bracket (locally procured).
–
Rack mount bracket:
For WJ-PR204/WJ-PR201: BY-HCA10A
For WJ-PR204E/WJ-PR201E: BY-HCA10CE
•
Available racks
–
EIA standard rack or equivalent (third party)
EIA19 type
•
Rack mounting screws
–
M5
´
12 mm {15/32 inches} screws
5.
Precautions before camera installations
PC200
•
Use the screws with the specifications shown on page 25 when mounting the
camera side unit to a ceiling or wall. Screws are included with camera side unit.
Use screws that are appropriate for the material of the ceiling or wall.
•
When mounting the camera side unit to a ceiling or wall (see page 25), do not
drive the screws into a soft material. Drive the screws into a secure, 25 mm
(1 inch) thick area of the ceiling or wall, such as a crossbeam, otherwise the
camera side unit may fall. If there is no crossbeam, place a board on the other
side of the ceiling or wall to make sure the camera side unit is securely mounted.
•
When mounting a camera side unit on a concrete or mortar ceiling or wall, use
a drill and anchors (locally procured, body diameter 4 mm {3/16 inches}) and
make holes using the following procedure.
i.
Mark points where you are going to make holes (2 places) according to the
position of the camera side unit.
ii.
Make holes in the areas that you marked with an electric drill.
•
Mortar ceilings break easily when drilling. Be careful of pieces of mortar
which may become loose and fall.
iii.
Insert the anchors (locally procured) into the holes and push them inside with
a hammer.
Caulk to waterproof
Drill for concrete (in case of tile, use a drill for tile)
•
Mount the camera side unit to a secure area and make sure that the anchors and
screws are secured.
18
Operating Instructions
1 Preface