Panasonic microP2 Handheld AVC-ULTRA HD Camcorder Operating Instructions - Page 178
Warning system, Cases indicated by error codes
View all Panasonic microP2 Handheld AVC-ULTRA HD Camcorder manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 178 highlights
Chapter 10 Maintenance and Inspection - Warning system Warning system If an error is detected immediately after the camera is turned on or during operation, the viewfinder, LCD monitor, and tally lamp indicate the error. Deal with the error by following the indications. Cases indicated by error codes Error code Display Description [E‑30] [TURN POWER OFF] [P2 CARD] An error occurred in the camera built-in memory because the P2 card being accessed was ejected. ffTally lamp flashes four times per second. [E‑31] [E‑33] [E‑35] [E‑36] [E‑37] [E‑39] [E‑64] [TURN POWER OFF] [SYSTEM MODE] System mode error occurred. ffTally lamp flashes four times per second. [SYSTEM ERROR] [CAMERA] [SYSTEM ERROR] [CODEC] [SYSTEM ERROR] [P2 SYSTEM] [SYSTEM ERROR] [P2CS] [SYSTEM ERROR] [INITIALIZE] [SYSTEM ERROR] [FRAME SIGNAL] (or no display) Camera unit error occurred. ffTally lamp flashes four times per second. Codec control error occurred. ffTally lamp flashes four times per second. P2 system error occurred. ffTally lamp flashes four times per second. P2CS microcomputer error occurred. ffTally lamp flashes four times per second. Video initialization error occurred. ffTally lamp flashes four times per second. Reference signal error occurred. ffTally lamp flashes four times per second. Behavior and cause ffCannot operate. ffFollow the message to turn off the power once and turn on the power again. ffEnsure that there is no error in the clips on the ejected card, and restore the clips as necessary. ffCannot operate. ffFollow the message to turn off the power once, turn on the power again, and check that there is no error display. ffThe operation stops. ffContact your dealer. ffThe operation stops. ffContact your dealer. ffThe operation stops. ffContact your dealer. ffThe operation stops. ffContact your dealer. ffThe operation stops. ffContact your dealer. ffThe operation stops. ffContact your dealer. Cases indicated by error messages During recording/playback Display [AUTH NG CARD] (slot number) [BACKUP BATT EMPTY] [CARD ERROR] (slot number) [DIR NG CARD] (slot number) [FAN STOPPED] [HIGH TEMPERATURE] [PB INTERMITTENT] (slot number) [PROXY ERROR] Description Behavior and cause CPS authentication of microP2 memory card has failed. The microP2 memory card whose CPS authentication failed cannot be recorded or played back. ffThe current operation will continue. ffSelect [AUTHENTICATE] in the main menu → [CLIP], and enter the password. Displays any reduced voltage detected on the backup battery in the internal clock when the power is turned on. ffThe current operation will continue. ffCharge the built-in battery. Displayed when an data error caused by the P2 card occurs during recording. Displayed after recording stops until the next operation. Also displayed for three seconds during playback when a P2 card error causes playback to stop. ffIf the error occurs during recording, the tally lamp flashes four times per second for approx. three seconds after recording stops. ffThe tally lamp does not flash when an error occurs during playback. ffThe operation will stop. ffAfter it stops, the P2 card on which the error occurred is write-protected. Replace the P2 card of the slot where the error occurred. The directory position is not correct. ffThe current operation will continue. ffMake a card backup immediately and format the card to use it again. Displayed when the fan motor stops. ffThe current operation will continue. ffIf the fan has stopped with error, stop using the camera immediately and consult your dealer. ffIf the fan has stopped, temperature of the camera will rise. Therefore, do not use the camera for a long period of time. ffThe current operation will continue. The temperature inside the camera is higher than that of ffTurn off the power of the camera, turn it on again, the normal conditions. and check recording and playback operations. If the problem persists, consult your dealer. Playback is interrupted on the SDHC/SDXC memory card. A card whose playback performance cannot be assured is inserted. ffThe current operation will continue. ffUse of microP2 or P2 memory card is recommended. An error occurred in the internal proxy module. ffThe current operation will continue. ffTurn off the camera and turn on it again to check the recording and playback. If the error continues to occur, please consult your dealer. - 178 -