Panasonic microP2 Handheld AVC-ULTRA HD Camcorder Operating Instructions - Page 36

Chapter 3 Preparation - P2 card P2 card access LED Flashing green slowly Off Card full Write protect Unrecordable card Slot that is not recording target Card not supported Illegal format No card Unauthenticated card P2 card status There is no free space on the P2 card. Reading only is possible. The write-protect switch on the P2 card is at the Protect position. Reading only is possible. Recording is not possible by the currently set recording format since the SD memory card, etc. is inserted. To record the card, change the recording format or use a P2 card. The card has been inserted into a different slot from the slot ([P2] or [microP2]) that was selected in the main menu → [RECORDING SETUP] → [REC MEDIA]. This card cannot be used on the camera. Replace the card. The P2 card is not properly formatted. Reformat the card. The P2 card is not inserted. The card is waiting to be recognized. This microP2 memory card cannot be authenticated. Select the main menu → [CLIP] → [AUTHENTICATE], and enter the password. For details, refer to "Manual CPS authentication" (page 112). Mode check display* [FULL] [PROTECTED] [REC IMPOSSIBLE] No display [NOT SUPPORTED] [FORMAT ERROR] [NO CARD] [AUTH NG] * Mode check is displayed on the LCD monitor screen or the viewfinder screen. For details, refer to "Screen status display" (page 142). P2 card recording time rr P2 cards supported on the camera Optional P2 and microP2 memory cards with a capacity of 4 GB to 64 GB can be used with the camera. (As of March 2014) @@NOTE tt AJ‑P2C002SG (2 GB) cards cannot be used. tt When AVC‑Intra 100 in 1080/59.94P or 1080/50P mode is selected, you cannot record to the following P2 cards. - P2 memory cards of R, A, or E series tt The driver installed on the camera may be required to be updated depending on the type of P2 card. (page 182) tt Refer to our support desk at the following website for the latest information not included in these operating instructions. http://pro-av.panasonic.net/ rr P2 card recording times (Example when a 64 GB card is used) 1080P System mode 1080i, 720P 480i, 576i Recording format (codec) AVC‑Intra 100 AVC‑LongG 25 AVC‑LongG 12 AVC‑Intra 100 AVC‑Intra 50 AVC‑LongG 50 AVC‑LongG 25 AVC‑LongG 12 DVCPRO HD DVCPRO50 DVCPRO DV Recording time Approx. 32 min Approx. 128 min Approx. 256 min Approx. 64 min Approx. 128 min Approx. 128 min Approx. 256 min Approx. 512 min Approx. 64 min Approx. 128 min Approx. 256 min Approx. 256 min @@NOTE tt The above table shows values for regular recording. With native recording, even longer recording times are available depending on the system mode. tt In the case of 32 GB P2 cards, the recording time becomes 1/2 of the above recording times, in the case of 16 GB P2 cards, the recording time becomes 1/4, and in the case of 8 GB P2 cards, the recording time becomes 1/8. tt Indicated capacities include management and other area, so the space available for recording is less than the values in the table above. Dividing clips recorded on P2 cards If P2 cards with a capacity of 8 GB or more are used on the camera, recording is automatically continued as another clip when a single continuous recording time exceeds the following times. When thumbnails for clips are handled (displayed, deleted, restored, etc.) on P2 devices, they can be handled as a single clip. Clips may be displayed as separate clips in nonlinear editing software and on a computer. When recording on microP2 memory cards that exceed 32 GB in AVC‑LongG codec, recording can be continued as the same clip by selecting [ONE FILE] from the main menu → [RECORDING SETUP] → [FILE SPLIT]. Recording format (excluding native recording) AVC‑I100 (1080P) Continuous recording time Approx. 3 min - 36 -