Panasonic microP2 Handheld AVC-ULTRA HD Camcorder Operating Instructions - Page 179
During thumbnail and menu operation, Maintenance and Inspection - Warning system
View all Panasonic microP2 Handheld AVC-ULTRA HD Camcorder manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 179 highlights
Display [PROXY REC WARNING] [REC IMPOSSIBLE] (slot number) [REC WARNING] [FRAME SIGNAL] [REC WARNING] [OVER MAX# CLIPS] [REC WARNING] [PULL DOWN] [REC WARNING] [PULL DOWN ERROR] [REC WARNING] [REC DATA] [RUN DOWN CARD] (slot number) [SD CARD] (slot number) [SLOT3 CANNOT REC] [microP2 SELECTED] [SLOT3/4 CANNOT REC] [P2 SELECTED] [TEMPORARY PAUSE] [IRREGULAR SIG] [VFR ON, NO AUDIO RECORDING] Chapter 10 Maintenance and Inspection - Warning system Description Behavior and cause A proxy data recording error occurred. ffThe current operation will continue. ffTurn off the camera and turn on it again to check the recording and playback. If the error continues to occur, please consult your dealer. An SDHC/SDXC memory card is inserted into the microP2 memory card slot. Recording to the SDHC/SDXC memory card is disabled. ffThe current operation will continue. ffRecord to microP2 or P2 memory cards. Displayed when a video or audio error occurs during recording. ffTally lamp flashes four times per second during continuous recording. ffThe current operation will continue. When input signals are disrupted, recording continues while disrupted images are recorded. Check the signal to be input to the camera. ffTurn off the power and on before using it again. Displayed when attempting to record in excess of the maximum total number of clips allowed for one P2 card. ffTally lamp flashes four times per second during continuous recording. ffThe operation will stop. ffReplace the P2 card or delete unnecessary clips. (Occurs during recording) The video pull-down sequence and time code values are not synchronized. ffTally lamp flashes four times per second during continuous recording. ffThe current operation will continue. ffCheck the signal. (Occurs at times other than during recording) The video pull-down sequence and time code values are not synchronized. ffThe current operation will continue. ffCheck the signal. Displayed when an error occurs in recorded data during recording. ffTally lamp flashes four times per second during continuous recording. ffThe operation will continue or stop. ffTurn off the power and on before using it again. The maximum number of overwrites has been exceeded. ffThe current operation will continue. ffReplacement of the P2 card is recommended. An SDHC/SDXC memory card is inserted into the microP2 memory card slot. ffThe current operation will continue. ffUse of microP2 or P2 memory card is recommended. Displayed when the card is inserted into the slot which is not selected as the recording slot. ffThe operation will stop. ffSet [P2] in the main menu → [RECORDING SETUP] → [REC MEDIA]. Displayed when the card is inserted into the slot which is not selected as the recording slot. ffThe operation will stop. ffSet [microP2] in the main menu → [RECORDING SETUP] → [REC MEDIA]. Correct recording is not possible due to disruption of input signals of the or terminal, etc., and recording is suspended temporarily. The clip will be divided. ffTally lamp flashes four times per second during continuous recording. ffThe operation will pause. ffRecording resumes when the signal returns to normal. However, during loop recording, recording does not resume. Native variable frame rate recording is performed. Audio can not be recorded. ffThe current operation will continue. During thumbnail and menu operation Display [AUTHENTICATION ERROR!] [CANNOT ACCESS!] [CANNOT CHANGE!] [CANNOT DELETE!] [CANNOT FORMAT!] [CANNOT RE-CONNECT!] [CANNOT REPAIR IN SELECTION!] [CANNOT REPAIR!] [CANNOT SAVE! FILE NAME IN USE] [CARD FULL!] [COPY IMPOSSIBLE. TOO LARGE CLIP CONTAINED! (CLIP NAME: XXXXXX)] [INVALID VALUE!] [LACK OF CAPACITY!] Description Manual authentication failed. Data cannot be accessed due to a content defect or some other reason. Behavior and cause Enter the correct password. Ensure the health of the media and the clips. For a clip with the mark, where a thumbnail cannot be generated, the thumbnail cannot be modified in the text memo position. The content versions do not match. Cannot delete. A P2 card problem or some other reason prevents formatting. Clips cannot be remerged because either clips not recorded across multiple P2 cards are selected or other reasons. Some of the selected clips cannot be repaired. Content that cannot be repaired is selected. A settings file of the same name exists on the SD memory card. The P2 card or SD memory card is full. Files exceeding 4 GB cannot be copied to P2 memory card or microP2 memory card with 32 GB or smaller capacity. The data value you entered is invalid. There is not enough recording capacity left on the card. Correct the settings and content to enable display of the thumbnail. Match the device and contents version. Check the P2 card. Check the selected content. Check the selected content. Check the selected content. Use another name to save the file. Insert a card with free space available. Copy to a microP2 memory card with 32 GB or larger capacity. Enter data within the normal range. Insert a card with sufficient recording capacity. - 179 -