Poulan 4400-4900-5400 User Manual

Poulan 4400-4900-5400 Manual

Get Poulan 4400-4900-5400 PDF manuals and user guides View all Poulan 4400-4900-5400 manuals
Add to My Manuals
Save this manual to your list of manuals

Poulan 4400-4900-5400 manual content summary:

  • Poulan 4400-4900-5400 | User Manual - Page 1
    Pout n 4400/4900/5400Counter Vibe chain saw CAUTION: Read Rules for Safe Operation Carefully. Note Special Instructions for operator's manual Record in the space provided below the model number and serial number of your saw. Bow Saw Users. Model No Serial No BEAIRD-POULAN/ WEED EATER Division
  • Poulan 4400-4900-5400 | User Manual - Page 2
    Carburetor Adjustment Chain Sharpening Trouble Shooting MODEL CU. IN. DISPLACEMENT SPARK PLUG SPARK PLUG GAP IGNITION MODULE AIR GAP OILER GUIDE BAR CHAIN BOW GUIDE FUEL MIX MUFFLER TABLE OF CONTENTS 3, 4 3, 4 7 4, 5 7 5 6 6 8, 9 10 11 12 13 SPECIFICATIONS 4400 4900 5400 4.2 in3 /69 cm3
  • Poulan 4400-4900-5400 | User Manual - Page 3
    the holes and attach securely with the screws provided. HAND GUARD MOUNTING INSTRUCTIONS 1. Assemble the hand guard to the bend in the handlebar as be tightened evenly to prevent breakage. 0 It 1O 0 . INSTALLING THE GUIDE BAR AND SAFETY CHAIN 1. Remove the bar mounting nuts. Using the scrench
  • Poulan 4400-4900-5400 | User Manual - Page 4
    jou- 0 0 Flange out or away from guide bar on both sides Figure 5 OPERATING INSTRUCTIONS Before Starting O Check the chain tension. Is the cool off. Wipe the bottom clean before storing. AUTOMATIC OILER: Your Poulan Chain Saw is equipped with an automatic oiler which delivers a constant flow
  • Poulan 4400-4900-5400 | User Manual - Page 5
    Throttle Detent will release automatically, allowing engine to idle. Note: Overchoking engine will cause it to flood. Should engine flood, repeat starting instructions with Choke Knob pushed in until engine starts. 1. If there is doubt about the direction of fall, use "notch" method described in
  • Poulan 4400-4900-5400 | User Manual - Page 6
    cut in a tree, do not carry a running saw while climbing. O Keep Both. Hands On The Saw - keep a firm grip. Figure 11 . O Be Sure Of Your Support - don't cut off balance. O Cut Up From The Bottom, Finish Down From The Top. 3 Debranching (Cutting the limbs from a fallen tree) O Cut On The Opposite
  • Poulan 4400-4900-5400 | User Manual - Page 7
    to install a .404 pitch sprocket which is included with the bow kit. BOW ASSEMBLY INSTRUCTIONS 1. Attach 1325 and 1326 spikes to bow guide with two (2) 625567 screws and two (2) 1615 locknuts. 2. Attach guard to bow guide with open side away from engine, using two (2) 1709 screws and two (2) 1725
  • Poulan 4400-4900-5400 | User Manual - Page 8
    saw with the engine stopped, the guide bar and chain covered and to the rear, and the muffler away from your body. All chain saw service other than the items listedin the operator'smanualmaintenance instructions, should be performed by competent chain saw service personnel. Conditions in Your Work
  • Poulan 4400-4900-5400 | User Manual - Page 9
    saw handles. • Do not let the nose of the guide bar contact a log, branch, the ground, or any from children. • Follow manufacturer's sharpening and maintenance instructions for the saw chain. • Always do your of the saw. DON'T LET GO. Your Poulan chain saw is a reliable and powerful cutting tool
  • Poulan 4400-4900-5400 | User Manual - Page 10
    bar, chain, and bar clamp completely assembled. The clutch can come off without the guide bar and chain completely assembled and serious injury could result. 1. Remove the cylinder cover and the high tension lead from the spark plug to prevent
  • Poulan 4400-4900-5400 | User Manual - Page 11
    CARBURETOR ADJUSTMENT (Model 4400/4900/5400) STOP THE ENGINE - Make sure you are using clean, fresh fuel mixture at the correct gasoline/oil ratio. THE AIR FILTER MUST BE CLEAN AND
  • Poulan 4400-4900-5400 | User Manual - Page 12
    when cutting. 3. Worn rails are shown in (3). This occurs most often at the guide bar nos . 4. Uneven rails are shown in (4). This will cause the saw tight. You must still be able to move the chain around the bar. 2. Clamp the guide bar in a vise. Don't clamp the chain! Clamp in the center of the bar
  • Poulan 4400-4900-5400 | User Manual - Page 13
    TROUBLE guide bar. 5. Chain on backwards. 6. Engine low on power. 1. Out of oil. 2. Dirty oil filter. 3. Guide problems service. 1. Fill tank. 2. Clean and replace. 3. Remove bar and clean. 1. See instructions - page 3 & 4. 2. See instructions - page 12. 3. Replace with new one. 4. See instructions
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
Pout
n
4400/4900/5400
Counter
Vibe
CAUTION:
Read
Rules
for
Safe
Operation
Carefully.
Note
Special
Instructions
for
Bow
Saw
Users.
chain
saw
operator's
manual
BEAIRD-POULAN/
WEED
EATER
Division
Emerson
Electric
Co.
5020
Flournoy
-Lucas
Road
Shreveport,
Louisiana
71109
Record
in
the
space
provided
below
the
model
number
and
serial
number
of
your
saw.
Model
No
Serial
No
Retain
these
numbers
for
future
reference.