ProForm 735 English Manual - Page 7

Secure the Crossbar with two M10 Nylon Locknuts

Get ProForm 735 PDF manuals and user guides View all ProForm 735 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

2. Press a 51mm x 76mm Inner Cap (53) into the top of the Left Upright (37). Note: Make sure the adjustment brackets are oriented as shown. Press a 2Ó Square Inner Cap (17) into each end of the Left Stabilizer (25). Press a 38mm Square Inner Cap (31) into the vertical tube on the Left Stabilizer. Insert four M10 x 62mm Carriage Bolts (33) up through the Left Stabilizer (25). Place the Left Stabilizer flat on the floor. Slide the Left Upright (37) onto the four M10 x 62mm Carriage Bolts (33) in the Left Stabilizer (25). Attach the Upright with four M10 Nylon Locknuts (11). Do not tighten the Nylon Locknuts yet. 2 Adjustment Brackets 11 53 37 31 11 11 17 17 3. Insert two M10 x 68mm Bolts (34) into an Upright 3 Support Plate (16). Next, insert the Bolts into the indi- cated holes in the Right Upright (1). While a second person holds the Right Upright (1), slide the bracket on the Crossbar (20) over the 1 two M10 x 68mm Bolts (34). Make sure that the Crossbar is turned so the decal is facing up. Secure the Crossbar with two M10 Nylon Locknuts (11). Attach the Crossbar (20) to the Left Upright (37) in the same manner. 34 16 25 33 33 37 11 20 11 Decal 11 11 16 34 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
7
17
11
17
33
25
33
31
11
11
3.
Insert two M10 x 68mm Bolts (34) into an Upright
Support Plate (16). Next, insert the Bolts into the indi-
cated holes in the Right Upright (1).
While a second person holds the Right Upright
(1)
, slide the bracket on the Crossbar (20) over the
two M10 x 68mm Bolts (34).
Make sure that the
Crossbar is turned so the decal is facing up.
Secure the Crossbar with two M10 Nylon Locknuts
(11).
Attach the Crossbar (20) to the Left Upright (37) in
the same manner.
16
34
37
1
3
2.
Press a 51mm x 76mm Inner Cap (53) into the top of
the Left Upright (37).
Note: Make sure the adjust-
ment brackets are oriented as shown.
Press a 2° Square Inner Cap (17) into each end of
the Left Stabilizer (25). Press a 38mm Square Inner
Cap (31) into the vertical tube on the Left Stabilizer.
Insert four M10 x 62mm Carriage Bolts (33) up
through the Left Stabilizer (25). Place the Left
Stabilizer flat on the floor.
Slide the Left Upright (37) onto the four M10 x 62mm
Carriage Bolts (33) in the Left Stabilizer (25). Attach
the Upright with four M10 Nylon Locknuts (11).
Do
not tighten the Nylon Locknuts yet.
2
37
53
11
11
20
Decal
11
11
34
16
Adjustment
Brackets