Reebok 710 Treadmill English Manual - Page 27

Troubleshooting

Get Reebok 710 Treadmill PDF manuals and user guides View all Reebok 710 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

TROUBLESHOOTING Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, see the front cover of this manual. SYMPTOM: The power does not turn on a. Make sure that the power cord is plugged into a surge suppressor and that the surge suppressor is plugged into a properly grounded outlet (see page 17). Use only a surge suppressor that meets all of the specications described on page 17. IMPORTANT: The treadmill is not compatible with GFCI-equipped outlets and may not be compatible with AFCI-equipped outlets. b. After the power cord has been plugged in, make sure that the key is inserted into the console. c. Check the power switch located on the treadmill frame near the power cord. If the switch protrudes as shown, the switch has tripped. To reset the power switch, wait for ve minutes and then press the switch back in. c c. Remove the key from the console, and then reinsert it. d. If the treadmill still will not run, please see the front cover of this manual. SYMPTOM: The console displays remain lit when you remove the key from the console a. The console features a display demo mode, designed to be used if the treadmill is displayed in a store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE INFORMATION MODE on page 25 to turn off the demo mode. SYMPTOM: The displays of the console do not function properly a. Remove the key from the console and UNPLUG THE POWER CORD. Remove the ve #8 x 3/4" Truss Head Screws (16). Carefully slide the Motor Hood (60) off. Tripped Reset SYMPTOM: The power turns off during use a 60 16 16 16 a. Check the power switch (see the drawing above). If the switch has tripped, wait for ve minutes and then press the switch back in. 16 b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for ve minutes, and then plug it back in. 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
27
Most treadmill problems can be solved by follow-
ing the simple steps below. Find the symptom that
applies, and follow the steps listed. If further assis-
tance is needed, see the front cover of this manual.
SYMPTOM: The power does not turn on
a.
Make sure that the power cord is plugged into a
surge suppressor and that the surge suppressor
is plugged into a properly grounded outlet (see
page 17). Use only a surge suppressor that meets
all of the speci
cations described on page 17.
IMPORTANT: The treadmill is not compatible
with GFCI-equipped outlets and may not be
compatible with AFCI-equipped outlets.
b.
After the power cord has been plugged in, make
sure that the key is inserted into the console.
c.
Check the power switch located on the treadmill
frame near the power cord. If the switch protrudes
as shown, the switch has tripped. To reset the
power switch, wait for
ve minutes and then press
the switch back in.
SYMPTOM: The power turns off during use
a.
Check the power switch (see the drawing above).
If the switch has tripped, wait for
ve minutes and
then press the switch back in.
b.
Make sure that the power cord is plugged in. If the
power cord is plugged in, unplug it, wait for
ve
minutes, and then plug it back in.
c.
Remove the key from the console, and then
reinsert it.
d.
If the treadmill still will not run, please see the front
cover of this manual.
SYMPTOM: The console displays remain lit when
you remove the key from the console
a.
The console features a display demo mode,
designed to be used if the treadmill is displayed in
a store. If the displays remain lit when you remove
the key, the demo mode is turned on. To turn off
the demo mode, hold down the Stop button for a
few seconds. If the displays are still lit, see THE
INFORMATION MODE on page 25 to turn off the
demo mode.
SYMPTOM: The displays of the console do not
function properly
a.
Remove the key from the console and
UNPLUG
THE POWER CORD.
Remove the
ve #8 x 3/4" Truss Head Screws (16).
Carefully slide the Motor Hood (60) off.
TROUBLESHOOTING
Reset
Tripped
c
60
16
16
16
16
a